manualshive.com logo in svg

Appareo Stratus ES, Installation Instructions Manual

Share
Download
Appareo Stratus ES Installation Instructions Manual Download Page 42

600840-000031 Stratus ES/ESG Installation Instructions 

Rev. 2.2 

Last Revised: February 20, 2018 

 

Page 42 of 45 

The screen displays a Built in Test 
(BIT) failure 
 
The display screen will display a 
warning message and a degraded 
state indicator 

 if any of 

Stratus ES/ESG’s BITs fail. 

The Stratus ES/ESG screen might display a warning 
message with the instructions below. Below is guidance 
regarding how to assess the failure: 

•

 

PRESS FUNC TO CLEAR

: A non-critical error has 

been detected. The transponder will run in a 
degraded state until the error is resolved. Contact 
Appareo for further assistance. 

•

 

PLEASE RESTART UNIT

: A critical error has been 

detected. Restarting the unit may fix the error. If the 
message returns after restarting, contact Appareo 
for further assistance. 

•

 

PLEASE SHUTDOWN UNIT

: A critical error has 

been detected. Power off the unit and do not turn it 
back on. Contact Appareo for further assistance. 

•

 

OVERHEATED

:

 

The transponder has overheated. 

Transponder function will resume when the 
transponder cools down. 

•

 

WAITING TO BE UNSTUCK

: A key has been 

depressed for more than 20 seconds. If a key is 
stuck, try to unstick the key. 

•

 

WAITING FOR RELEASE

: The external 

suppression input is constantly in a suppressed 
state. Contact Appareo for further assistance. 

•

 

ATTEMPTING TO RECOVER

: A squitter rate error 

has been detected. The transponder may recover 
itself, but if it does not, restart the unit. If the 
message returns after restarting, contact Appareo 
for further assistance. 

 
 

 

Summary of Contents for Stratus ES














































Reviews:

No comments

Brands by name

Popular brands

Load more brands