manualshive.com logo in svg

Appareo Stratus ES, Installation Instructions Manual

Share
Download
Appareo Stratus ES Installation Instructions Manual Download Page 33

600840-000031 Stratus ES/ESG Installation Instructions 

Rev. 2.2 

Last Revised: February 20, 2018 

 

Page 33 of 45 

5.5. 

EMI check 

NOTE:

 The EMI testing shall not be performed until after the system functional ground test is 

complete and passes. 

 Communications 

(i)  Cockpit intercom 

Using the cockpit intercom, verify interference-free communications between the crew while 
monitoring the effects of Stratus ES/ESG. 

(ii)  Cabin paging 

Verify that cabin paging is functioning clearly while monitoring the effects of Stratus ES/ESG. 

 VHF communications 

Set VHF communications radios to multiple frequencies and monitor the effects of 
Stratus ES/ESG while transmitting and receiving. At a minimum, the frequencies listed below 
should be tested, in addition to locally available frequencies. Each transmission should occur for 
35 seconds for each frequency.  

Verify that the NIC value on the GPS receiver diagnostic screen is 7 or greater. 

Test each frequency in 1 MHz increments between 118 -136.000 MHz. 

Test the following frequencies for VHF radios with 25kHz spacing: 

121.150 

 

121.175 

 

121.200 

 

121.225 

121.250 

 

131.200 

 

131.225 

 

131.250 

131.275 

 

131.300 

 

131.325 

 

131.350 

 

Test the following frequencies for VHF radios with 8.33kHz spacing: 

121.185 

 

121.190 

 

130.285 

 

131.290 

 

 HF communications 

If the aircraft is equipped with HF communications radios, set to multiple frequencies and 
monitor effects of Stratus ES/ESG while transmitting and receiving. Record the frequencies 
tested: 

 SATCOM communications (Stratus ESG only) 

If aircraft is equipped with a SATCOM system, operate the SATCOM equipment while 
monitoring the GPS CN0 diagnostic screen. Verify that the CN0 values on the GPS receiver 
diagnostic screen do not drop by 2 dB or more.

 

Summary of Contents for Stratus ES














































Reviews:

No comments

Brands by name

Popular brands

Load more brands