manualshive.com logo in svg

APPA 30R, Instruction Manual

Share
Download
APPA 30R Instruction Manual Download Page 2

1 

  
 
 

 Safety Information 

  

˙ 

Individual protective equipment must be used if hazardous live parts in the installation where measurement is to  

     be carried out could be accessible.

  

˙ 

The barrier on the JAW is indicating the limit of safe access of the hand-held  part, do not over the barrier when  

     in normal use. 

˙ 

Do not use a flexible current sensor if the inner contrasting color of the insulation of the flexible cord is visible. 

˙ 

If the equipment is used in a manner not specified by the manufacturer, the protection provided by the 

     equipment may be impaired. 

CAT.

Ⅱ

-

 

Is for measurement performed on circuits directly connected to the low voltage installation. 

CAT.

Ⅲ

-

 

Is  for measurement performed in the building installation. 

Warning

  

. . . . . . . . . .

 . . . . . . . . . .
 . . . . . . . . . .
 . . . . . . . . 

Safety sheet

 . . . . . . . . .  
 . . . . . . . . . .
 . . . . . . . . . .
 . . . . . . . .

 . . . . . . . . .

 

 

Read First

 

Summary of Contents for 30R


























Reviews:

No comments

Brands by name

Popular brands

Load more brands