background image

7

CONVENTIONAL DETECTORS

All data is supplied subject to change without notice.
Specifications are given at 23°C and 50% relative humidity unless otherwise stated.

DETECTOR OPERATING  PRINCIPLES

Principle of detection:

 

Photo-electric detection of light scattered by smoke

particles over a wide range of angles. The optical 

arrangement comprises an infra-red emitter with a prism 

and a photo-diode at 90° to the light beam with a wide 

field of view. The detector’s microprocessor uses algorithms 

to process the sensor readings.

Sampling frequency:

 

Once every 4 seconds

ELECTRICAL

Supply voltage:

 

8.5—33V DC

Supply wiring:

 

2 wires, polarity sensitive

Maximum polarity reversal:

 200ms

Power-up time:

 

<20 seconds

Minimum ‘detector active’ voltage:

 6V

Switch-on surge current at 24V:

  95µA

Average quiescent current at 24V:

 95µA

Alarm current:

 

At 12 volts 

20mA

 

At 24 volts 

40mA

Alarm load:

 600Ω

Holding voltage:

 5–33V

Minimum holding current:

 8mA

Minimum voltage to light 

5V

alarm LED:

 

Alarm reset voltage:

 <1V

Alarm reset time:

 

1 second

Remote output LED 

1.2kΩ connected to negative supply

(–) characteristic:

 

  

MECHANICAL

Material:

 

Detector and base moulded in white polycarbonate. 

Alarm Indicator:

 

Integral indicator with 360° visibility

 

(See Table 3 on page 13 for details of flash rate)

Dimensions:

 

97mm diameter x 31mm height

 

100mm diameter x 46mm height (in base)

Weight:

 

Detector  

75g

 

Detector in base 

135g

ENVIRONMENTAL

Temperature:

 

Operating and storage temperature 

–40°C to +70°C

 

 

 

 

(no condensation or icing)

Humidity:

 

0% to 98% relative humidity (no condensation)

Wind speed:

 

Unaffected by wind

Atmospheric pressure:

 

Insensitive to pressure

IP rating to EN 60529: 1992*:

 23D

Electromagnetic Compatibility: 

The detector meets the  requirements of EN 61 000-6-3

 

for emissions and BS EN50 130-4 for susceptibility. 

*The IP rating is not a requirement of EN 54 since smoke detectors have to be open in order 

to function. An IP rating is therefore not as significant as with other electrical products. 

TECHNICAL DATA

ENVIRONMENTAL 

PERFORMANCE

Orbis optical detectors operate over a 

broad range of voltages at extremes of 

temperature. Thus the operating voltage 

is 8.5V to 33V at –40° to +70°C, a unique 

achievement for a conventional smoke 

detector.

Summary of Contents for ORB-BA-10008-APO

















Reviews: