background image

833/834 CONTROL BOARD ADJUSTMENTS

 

    

OFF        ON

 

Learn Mode 

 

When switch #9 is in the ‘ON’ position, the controller is in learn mode.  Learn mode is used to ‘train’ the 
controller on the installation.  Specifically the controller monitors the current draw and stroke length during 
learn mode.  This allows the controller to automatically set the auto reverse sensitivity of the installation in 
addition to determining when to engage the soft stop feature. 
 
When the controller is initially installed, it must be put into learn mode.  The gate should be fully opened 
and closed 3-5 times and partially opened and closed 3-5 times to allow the controller to adjust to the 
weight and size of the gate.  Program switch #9 should then be moved to the ‘OFF’ position to exit learn 
mode.   
 
Any changes to the condition of the gate (i.e. cold weather, rust, etc.) may require the controller to be put 
into learn mode to train the controller once again. 
 
Note: The controller must be put into learn mode any time that it is disconnected from the power supply. 
 
Switch #9 Must Be In The OFF Position During Normal Operation. 

Program Switch #9 

“Learn Mode” 

14 

Summary of Contents for 7100UL


















Reviews: