Apollo Sprayers MAXI-MISER PBC7600-GTO Instruction Manual Download Page 15

14 

 

9.  Record of Spray Gun Maintenance

 

 

Date

 

Hours Of Use

 

Total Hours

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10.  Troubleshooting

 

 

1.    Your paint cup is full of material, the HVLP air is supplied to the spray gun, trigger is pulled and no paint comes out

 

Reason: Cup not pressurizing.

 

A. Check Non-return valve installed correctly. (Black side towards cup)  
B. Check Non-return valve. Clean or replace as necessary.

 

C. Check Air feed connector has a blockage. Check/clean as necessary 
D. Check to make sure the cup is clamped tight.

 

E. Check the cup top gasket to make sure that the gasket is not damaged or worn and that the cup is sealing 
correctly on it. Replace if necessary.

 

F. Gravity cup: check air pressure feed line is properly connected and not crimped.

 

G. Gravity cup: check the cup top gasket to make sure that the gasket is not damaged or worn and that the cup is 
sealing correctly on it. Replace if necessary.

 

 

2.    If you think that you are getting too much “overspray” Try:

 

A. Moving the spray gun closer to the work (Turbine or compressor).

 

B. Reduce the fluid flow 

 

C. Considering using a smaller nozzle and needle assembly (Turbine or compressor 
D. Reduce air pressure (Compressor or Precision series turbines)

 

 

3.    If the sprayed surface is not flat and level after drying (orange peel effect) Try:

 

A. Increasing air pressure (Compressor or Turbine Models 835VR, 1050VR, 1100 & 1200, POWER-5, 
PRECISION-5, PRECISION-6)  
B. Thin the coating more. (Turbine or compressor)

 

 

4.    If the finish looks like “dry mist” or if you think the speed of the application is too slow. Try: 

A. Increasing the fluid flow

 

B. Moving the spray gun slower

 

C. Moving the spray gun closer to the work piece

 

D. Thin the coating more.

 

 

5.    Fan Pattern Control Ring is hard to rotate or will not turn. Try:

 

A. Loosening the fluid nozzle slightly. (Caution – Do not loosen to much or leakage will occur)

 

 

6.    When rotating Fan Pattern Control Ring you only get a round spray pattern.

 

Try:  Locate  part  (#8)  Air  Distributor  Plate  which  is  attached  to  part  (#7)  Air  Distributor.  The  position  of  the  air 
distributor plate is critical to the operation of the Fan Pattern Control Ring. (See page 29 for correct and incorrect 
position). Adjust if necessary.

 

 

If you have any additional questions, please refer to our website located at www.hvlp.com or call our technical service line

 

at 888-900-4857.

Summary of Contents for MAXI-MISER PBC7600-GTO





















Reviews: