Aplex AEx-P526 User Manual Download Page 37

Page: 37 / 71

AEx-P526 User Manual

[Never]

Boot option filter

[UEFI and Legacy]

[Legacy only]

[UEFI only]

Launch PXE OpROM poli

[Do not Launch]

[UEFI only]

[Legacy only]

Launch Storage OpROM

[Legacy only]

[Do not Launch]

[UEFI only]

Launch Video OpROM po

[Do not Launch]

[UEFI only]

[Legacy only]

Other PCI device ROM

[UEFI OpROM]

[Legacy OpROM]

3.7 Security Settings

Aptio Setup Utility

American Megatrends, Inc.

Main

Advanced

Chipset

Boot

Security

Save & Exit

Password Description

If ONLY the Administrator

’s password is set,

Then this only limits access to Setup and is

Only asked for when entering Setup.

If ONLY the User

’s password is set, then this

Is a power on password and must be entered to

Boot or enter Setup. In Setup the User will

Set Administrator

Password

Summary of Contents for AEx-P526








































































Search results

Summary of Contents for AEx-P526

Reviews:

Related manuals for AEx-P526

Brands by name

Popular brands

Aplex AEx-P526, User Manual

Search results

Summary of Contents for AEx-P526

Reviews:

Related manuals for AEx-P526

Brands by name

Popular brands