background image

iv

Tel: 1/888/525-7300 • Fax: 1/435/753-7490 • www.apgsensors.com • [email protected]

Warranty and Warranty Restrictions

APG warrants its products to be free from defects of material and workmanship and will, without charge, 
replace or repair any equipment found defective upon inspection at its factory, provided the equipment has 
been returned, transportation prepaid, within 24 months from date of shipment from factory.   

THE FOREGOING WARRANTY IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES NOT EXPRESSLY SET 
FORTH HEREIN, WHETHER EXPRESSED OR IMPLIED BY OPERATION OF LAW OR OTHERWISE INCLUDING 
BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR 
PURPOSE.             

No representation or warranty, express or implied, made by any sales representative, distributor, or other 

agent or representative of APG which is not specifically set forth herein shall be binding upon APG. APG shall  

not be liable for any incidental or consequential damages, losses or expenses directly or indirectly arising 
from the sale, handling, improper application or use of the goods or from any other cause relating thereto 
and APG’s liability hereunder, in any case, is expressly limited to the repair or replacement (at APG’s option) 
of goods.   

Warranty is specifically at the factory. Any on site service will be provided at the sole expense of the 
Purchaser at standard field service rates.   

All associated equipment must be protected by properly rated electronic/electrical protection devices. APG 
shall not be liable for any damage due to improper engineering or installation by the Purchaser or third 
parties. Proper installation, operation and maintenance of the product becomes the responsibility of the 
user upon receipt of the product.   

Returns and allowances must be authorized by APG in advance. APG will assign a Return Material  
Authorization (RMA) number which must appear on all related papers and the outside of the shipping 

carton. All returns are subject to the final review by APG. Returns are subject to restocking charges as 

determined by APG’s “Credit Return Policy”. 

Summary of Contents for LPU-2127






















Reviews: