Apevia X-Telstar Jr Install Manual Download Page 7

Page: 7 / 13

7. Temperature probe setup:

4.2 From the outside rear of the case,
push PCI slot cover(s) toward the
inside of the chassis.

4.1 First, remove the PCI slot covers.
      Firmly press point A with thumb,
      while pulling point B with index
      finger to open the latch.

4. Install PCI components:

4.3 Read your PCI expansion card’s
      documentation. Install PCI card
      into correct slot for your card
      type (x1, x16, etc.).

6.1 Daisy chain the fans to be regulated
      using the fan speed controller. Con-
      nect male to female ends and plug
      the last male end into the fan
      controller connector labeled ‘OUT-
      PUT’. The connector labeled ‘INPUT’
      is then plugged into the power
      supply.

6.2 Use the fan controller knob on the
front panel to regulate the airflow
and fan noise.

6. Case fan setup:

4.4 Once the card is seated firmly,
      return latch to the initial position.
      A ‘click’ will be heard when fully
      engaged.

7.3 Place the other probe labeled ‘HDD’
on the hard-drive’s surface. Thermal
tape should be used for best results.

Note: You may also leave a sensor loose in the chassis in order to monitor
the ambient system temperature. DO NOT place the sensor directly on the
CPU as it will damage the sensor.

7.2 Place one of the probes on any ‘fin’ on
      the CPU’s heatsink and tape in place.
      Thermal tape should be used for best
      results.

7.1 Locate the device temperature
probes.

5. Connect case leads to motherboard:

5.1 Locate the top panel leads. Your
      motherboard user’s manual will
      provide schematics. The triang-
      ular markings      on the leads
      indicate positive wires.

5.2

Locate front panel leads. LED leads

      are located near the right-side panel.
      The Power/Reset/Speaker leads can
      be accessed by removing the left
      panel. Refer to your motherboard
      user’s manual for placement schem-
      atics.

(Remove right-side panel to better access wiring.)

7.4 Monitor system temperatures from
the front panel LCD.

10. USB/1394/Audio cable pin assignments:

9. Complete the installation:

9.3 With all components properly installed, gently
      return side panels to their original positions
      and replace all screws. Congratulations! You
      have completed assembly of the X-Telstar Jr.

8. LED display features:

8.2 The 5V/12V monitor displays the current voltage
values of the 5 and 12 volt rails respectively.
Red areas indicate very low/high voltages.

8.1 The fan monitor displays the percentage
of total RPMs currently being used.

8.4 The “Voice Unit” display allows you to
monitor dynamic audio gain and
gain reduction levels.

8.3 TMPE1 and TMPE2 display the current
      temperatures of components that have
      temp. sensors attached. The H.D.D
      indicator displays hard drive activity.

9.1 Connect the two Power LEDs. The LED behind
the Apevia logo is powered by a 2-pin connector
consisting of a blue/white wire pair.

9.2 Plug in the LED, which is powered by a 2-pin
lead consisting of a black/red wire pair.

3.5 Align rails with hard-drive bay and
insert.

3.4 Attach 1 mounting rail to each side
of each hard-disk drive.

3.2 For 5 1/4” drives, align the device
      with the drive bay and insert. Do
      the same for 3 1/2” drives using
      the two lower drive bays.

3.3 Slide the blue drive-rail forward
      and push the clamp downwards
      to engage locking mechanism.
      No screws are necessary, but
      can be used optionally on opti-
      cal and floppy drive bays.

1.4

Install power supply on top of

mounting ledges.

NOTE: Touch an unpainted metal section of the chassis to discharge
static electricity before handling PC components. An anti-static wrist
strap should also be worn to further minimize the possibility of damage.

3.1 To install an optical or floppy drive,
      first remove the metal shield that
      sits behind each drive bay cover.
      This must be done from the inside
      of the case. Next remove the drive
      bay covers by using a screwdriver,
      and forcing them out from behind.

3. Install 3½” and 5¼” drives

2.2

If your motherboard included an

      IO shield, you must remove the
      X-Jupiter Jr.’s IO shield. Use
      thumbs or other object to push
      shield inward (cover area with a
      cloth to avoid injury from metal
      edges!).

2.1 Refer to the motherboard holes
      index for standoff placement for
      your motherboard type. A full
      ATX (12”x9.6”) board will use
      notches A1-A9. Some mother-
      boards may not use all notches.
      Use any notches that line up
      with your motherboard.

2.3 Put brass standoffs in place. Align
      motherboard with standoffs and
      mount to case. This ATX mother-
      board (12”x8.3”) only used notches
      A1-A6. M8 was also used since it
      lined up.

2. Motherboard installation:

1.6 Fasten screws.

1.5 Make sure that the power supply is
correctly installed, and that screw
mount points are aligned.

1. Power Supply installation:

1.1 Remove thumbscrews from the
rear of the X-Telstar Jr.

1.3 Likewise for the window version;
      grab the notch on the left panel
      and pull to release.

NOTE:

CPU and memory installation is not covered in this

manual. Please refer to each components’ documentation
for instructions.

25cm Fan version

Window version

Motherboard installation..................................1