Recessed
Mounting
The surface mounted unit which utilizes the standard 2-3/4”
thick Visuline cabinet (2300.3 Series), is the ONLY display that
is shipped, ready to install. For all other Visuline series, the
display components must be removed to expose the internal
mounting structure.
The method which the display component is assembled and/or
fastened into the cabinet, varies with each display option. When
Visuline has different display components, there may be
multiple fastening methods. The following are standard
instructions for removing various display components.
NOTE: Retaining methods may vary from those shown. If
you are not sure how to remove the display components,
contact APCO at 404-688-9000.
Directory
A Directory
display with molded plastic message strips utilizes a
one-piece acrylic back-up and is secured into the cabinet with
velcro or preslock fasteners.
1.
Remove 6 or so message strips from bottom right corner
of display.
2.
Using suction cup tool provided, grasp display backer and
pull entire panel out of housing. NOTE: The bottom
message strip in each column is permanent. Therefore,
maintaining an upright position will keep messages from
falling out.
Directory
A Directory
display with aluminum or plastic SignBands is
constructed with removable columns. Each is secured into the
cabinet with velcro or preslock fasteners.
1.
Use Messageband removal tool provided and remove 2 or
so Signbands from bottom of each column.
2.
Grasp and pull columns out of housing. Note orientation of
SignBands and columns to assure proper repositioning.
Important: Far right column fabrication requires it to be
replaced into its original location.
Visuline Cabinet
LP Cabinet
Full Recessed Mounting
(2300.2 Series)
Before installing the Full Recessed Visuline, read “Cavity
Requirements” on previous page.
In a Full Recessed application, a 1” wide by 1-1/2” deep reveal
is secured to the cabinet, maintaining the necessary clearance
for proper door operation. This space is continuous around the
full perimeter and must not be obstructed.
IMPORTANT: Do not utilize the reveal or reveal trim as a
structural support for mechanical fastening.
Continuous Angle Trim
(Standard)
As a standard, full recessed Visulines are provided with a 1”
wide Continuous Angle Trim. The trim is attached to the
perimeter reveal and is used to conceals the cavity’s
Rough
opening. Cavity opening should be squarely constructed to
within 1/8”. Verify by measuring diagonal from corner to
opposite corner. Product Shop Drawings illustrate
recommended installation clearances.
No Trim
(Optional)
In those applications where decorative trim is completely
undesirable, cavity opening and returns must be
finished
. Cavity
must be constructed accurately in terms of both size and
squareness. It will be important however, that the 1” reveal
remains for proper door operation. Product Shop Drawings
illustrate recommended installation clearances.
Flat Bar Trim
(Optional)
When the 1” wide Continuous Angle Trim is undesirable, a 1/8”
wide Flat Bar Trim can be used. Cavity will become a
Finished
opening. It will be smaller in size and must be constructed
squarely. Measure diagonal from corner to opposite corner.
These dimensions must be equal. Product Shop Drawings
illustrate recommended installation clearances.
APCO
388 Grant Street, SE, Atlanta, Georgia USA 30312-2227 Telephone (404) 688-9000 www.apcosigns.com
IS309
APCO
388 Grant Street, SE, Atlanta, Georgia USA 30312-2227 Telephone (404) 688-9000 www.apcosigns.com
IS309
06/28/01
Visuline
®
2300 Series
Non-Illuminated Display System
06/28/01
Visuline
®
2300 Series
Non-Illuminated Display System
Remove Display
Components
Full Recessed Mounting
(2300.2 Series)
Molded Plastic Message Strips
Aluminum & Plastic SignBands
Surface Mount 2-3/4”
Visuline Cabinet
No pr
eparation necessary
.
Ready for installation
Continuous
Angle Trim
(Rough Opening)
Mounting
holes &
anchors by
installer
2-5/8" (Min)
1" Reveal
(Min)
Flat Bar
Trim
(Finished
Opening)
1" Reveal
(Min)
Mounting
holes &
anchors by
installer
No Trim
(Finished
Opening
& Returns)
Mounting
holes &
anchors by
installer
1" Reveal
(Min)
2-3/4" (Min)
2-3/4" (Min)
3-3/8" (Min)
3-1/2" (Min)
3-1/2" (Min)
Step.2
Grasp column (& header)
assemblies & pull out
message strips
Step.1
Unclip lower strips using
MessageBand removal tool
Step.2
Use suction cup tool
& pull out display
Step.1
Flex & remove lower
message strips
