background image

APANTAC LLC 

www.apantac.com 

16

 

OG-US-4000 User Manual 

COPYRIGHT and TRADEMARK 

All rights reserved by APANTA LCC, Portland, Oregon, USA. No part of this document may be reproduced in any form 
or by any means without written permission from the product manufacturer. Changes are periodically made to the 
information in this document. They will be incorporated in subsequent editions. The product manufacturer may 
make improvements and /or changes in the product described in this document at any time. 

All the registered trademarks referred to this manual are belonging to their respective companies. 

 

WARRANTY STATEMENT 

Apantac LLC (herein after referred to as “Apantac”) warrants to the original purchaser of the products manufactured 
by Apantac (the “Product,”) will be free from defects in material and workmanship for a period of three (3) year 
from the date of shipment of the Product to the purchaser. 

If the Product proves to be defective during the three (3) year warranty period, the purchaser’s exclusive remedy 
and Apantac’s sole obligation under this warranty is expressly limited, at Apantac’s sole option, to: 

a)  repair the defective Product without charge for parts and labor or,  

b)  provide a replacement in exchange for the defective Product or, 

c)  if after a reasonable time, is unable to correct the defect or provide a replacement Product in good working or-

der, then the purchaser shall be entitled to recover damages subject to the limitation of liability set forth below. 

 

Limitation of Liability 

Apantac’s liability under this warranty shall not exceed the purchase price paid for the defective product. In no event 
shall Apantac be liable for any incidental, special or consequential damages, including without limitation, loss of prof-
its for any breach of this warranty.  

If Apantac replaces the defective Product with a replacement Product as provided under the terms of this Warranty, 
in no event will the term of the warranty on the replacement Product exceed the number of months remaining on 
the warranty covering the defective Product. 

Equipment manufactured by other suppliers and supplied by Apantac carries the respective manufacturer’s warranty. 
Apantac assumes no warranty responsibility either expressed or implied for equipment manufactured by others and 
supplied by Apantac. 

This hardware warranty shall not apply to any defect, failure or damage: 

a)  Caused by improper use of the Product or inadequate maintenance and care of the Product; 

b)  Resulting from attempts by those other than Apantac representatives to install, repair, or service the Product; 

c)  Caused by installation of the Product in a hostile operating environment or connection of the Product to incom-

patible equipment; 

Summary of Contents for OG-US-4000 Series



















Reviews: