LINK
Open Terminal
RDY
MONITOR
SET
SET
24V
24V
LG
0V
DN
DP
DP
DN
24V 24V DP DP
LG 0V DN DN
■
Terminal layout
* The total length refers to
the total of the used cables.
Eject check switch
(Lever type)
Included
-A027XB02*2P 2/5-
A027XB-02
□
2-P
A027XB-02
□
2-P
A027XB-02
□
2-P
●
Transmission line (Bitty line)
Connect transmission lines
DP
and
DN
correctly.
●
Installation of transmission lines
Keep route transmission lines away from high-voltage and power cables.
Assign one transmission cable to one system of
AB023
-
□□□
. If multiple systems are used, assign a cable to each system.
If multiple systems are combined by a multi-wire cable, a malfunction may occur.
●
AnyWire transmission line error
When the transmission line is not working properly,
output is reset
.
●
Power supply to the AnyWire System
Install an
AnyWire
system-dedicated power supply to provide 24V DC power.
1
2
4
8
16
32
64
128
LINK
ADDRESS
ON
A027XB-02G2-P
ADDRESS No.
1
2
4
8
16
32
64
128
LINK
ADDRESS
ON
A027XB-02G2-P
ADDRESS No.
1
2
4
8
16
32
64
128
LINK
ADDRESS
ON
A027XB-02G2-P
ADDRESS No.
Eject indicator lamp
Master
30m or less
10m
or less
40-42 units
Pay attention to crimping direction of the link connector.
Improper connection results in malfunction or failure.
The hinge part side of the connector cover is the black line.
For details of link connector pressure welding work, refer to “How to pressure-weld link connector to flat cable” in our separate manual.
(Contact our Sales Department.)
At time of
terminal treatment
At time of
intermediate
treatment
Connector cover
Connector cover
Terminator AT0
LED
Black (DN)
White (DP)
■
Transmission distance
within the maximum length
of 100 m
24V DC stabilized
power supply for
general-purpose
24V
0V
DP
DN
: Green
: White
: Red
: Black
24V
0V
DP
DN
: Green
: White
: Red
: Black
24V
0V
DP
DN
: Green
: White
: Red
: Black
■
Wiring of POKA-YOKE Terminal
Manufacturer: Sumitomo 3M Limited
Applicable connector: Link connector
Cable used: 0.75mm
2
/4-wire flat cable
Applicable connector: FK4-075-100 (100m)
Cable used: 0.75mm
2
/4-wire flat cable
Applicable connector: FK4-075-100 (100m)
AB023-C1L
Input: 256 points
Output: 256 points
AB023-D1
Input: 256 points
Output: 256 points
FG
DG
SLD
DB
DA
CC-Link
Bit distribution I/O
terminal
DeviceNet
Bit distribution I/O
terminal
-V
+
V
CANLDrain
CANH
Connector layout
Type
Compatible Open Bus
[Connection Example]
Install an AnyWire
dedicated power
supply to supply to
the entire system.
24V DC stabilized
power supply set
voltage 26.4V.
Select capacity 1.3
times of required
consumption
current.
Transmission line consists of
four wires including power
supply by our flat cable
(FK4-075-100).
Under this condition, number
of units of A027XB-02
□
2-P
connectable to
AB023-
□□□
is up to 128
units per one system.
The terminator (AT0) is a composite element to
stabilize the transmission wave form.
Connect it at a position at the furthest end from
the master in the transmission line.
Note that it has own polarities.
(The LED lights up in a normal state.)
Improper connection may cause a malfunction
or a failure.
In order to turn ON the eject
check switch without fail, tilt
the lever at least approximately
30°or more.
The lever is allowed to be tilted
in any direction.
When connecting 128 units, refer to
the following configuration as an
example of using power efficiency
most efficiently.
○
Use the cable with a connector protruding from the back
of the unit.
○
Connect the cable, being careful not to reverse the
connection or cause a short circuit.
○
When swaging by the link connector, we recommend
using a dedicated tool that can realize stable work
quality.
(L-TOOL-N: SUZUDEN CORPORATION)
When making the connection, make sure that the
cable is not under tension.
In addition, do not fix the unit while the cable is
under tension.
Trunk line side
If a shock of 0.49 G or greater is applied to the
eject check switch, it may cause damage.
Do not force the lever, such as by "twisting it"
or "pulling it downward." Doing so may damage
the eject check switch.
CAUTION
CAUTION
CAUTION
CAUTION
CAUTION
