background image

Configuration

24 (124)

5.7

Date and Time

5.7.1

Date and Time Setting

The time calibration function is based on information from an NTP server or user specified time
and date, allowing functions such as automatic warning emails to include a time and date stamp.

The switch has no real-time clock. When there is no NTP server on the LAN or Internet
connection, Current Time must be set manually after each reboot.

Fig. 7

Date and Time Setting

Configure the Date and Time settings:

Current Time

Set the time manually or click

Get Time from PC

to get the PC time setting.

Time Zone

To adjust the time zone based on the user area, select a

Time Zone

.

NTP

To Enable NTP Client update, select the checkbox.
Make sure that the switch is connected to the internet.
The system will send request packet to acquire current time from the NTP server that assigned.

1st Time Server
2nd Time Server

Select the NTP Server from the list, which should adjust the User system time.

Daylight Saving Time Enable or Disable Daylight Saving Time.

Daylight Saving Start
Daylight Saving End

When Daylight Saving Time is Enabled, set the Start and End time.

To apply the settings, click

Submit

.

To cancel the changes, click

Cancel

.

Anybus

®

Managed Industrial L3 Switch User Manual

SCM-1202-151 1.1 en-US

Summary of Contents for AWB5011































































































































Reviews: