Anthro
Corporation Technology Furniture
®
10450 SW Manhasset Drive Tualatin, Oregon 97062 1-800-325-3841
anthro.com
Step 2
(uses the 3-Way Wrench)
Unpack the remaining Adjusta Mechanism components
and arrange them as shown at right.
Place one Crossbar end onto the lower Crossbar
“Button” and Threaded Bolt (located on each of the Arm
Mechanisms). Secure the Crossbar to the Arm Mechanism
using one
5
/
16
" Hex Nut onto the Threaded Bolt.
Repeat for remaining Crossbar end and Arm Mechanism.
5
/
16
" Hex Nut
(included with 225-5548-00)
DETAIL VIEW
Arm Mechanism
Threaded
Bolts
5
/
16
" Hex
Nut
Paddle
Brake/Paddle
Assembly
Arm Mechanism
Crossbar
Lower Crossbar
‘Button’
NOTE: it is very important that you attach the Crossbar
ONLY to the Lower Crossbar Button.
Step 1a
Your Adjusta Mechanism comes un-assembled and is
boxed separately inside the Adjusta Unit package.
Begin to assemble the Mechanism by first locating the Adjusta
Crossbar and Brake/Paddle Assembly, position it as shown at
right. Depress the Paddle once to free the Brake Shaft.
Place the Brake Shaft between the two center Crossbar
Flanges. Insert the Post through both center Crossbar
Flanges and Brake Shaft.
Cotter Pin
(included with 225-5548-00)
Center Crossbar Flanges
Cotter Pin
Step 1b
Install the Cotter Pin through the single opening of the
Post to secure into place.
NOTE: included with Adjusta Mechanism is a small bag of
Hardware containing the (1) Post, (1) Cotter Pin, (2) Hex Nuts,
(2) Wood Screws, & (2) Cable Mounts.
Post
(included with 225-5548-00)
Brake Shaft
Brake/Paddle Assembly
Crossbar
Post
FAJ60zz/xx3
Step 9
Position a Cross End on the opposite end of the Buttress
installed during Step 8.
Insert a Button Head Screw from the rear of the Buttress,
through the Cross End and capture on the opposite side
using a Keps Nut.
NOTE: Just hand tighten the Keps Nut for now.
(
1
/
4
-20 X .50") Button Head Screw
325-5003-00
(
1
/
4
-20) Keps Nut
325-5130-03
Keps Nut
Button Head Screw
Cross End
Support Screw
325-5010-00
Step 10
(requires the 3-Way Wrench)
Rotate the Buttress and Cross End upward to align the
holes on the Cross End with two corresponding holes
on a Vertical Leg.
Secure the Cross End to the Leg using two Support Screws.
Repeat Steps 8, 9 & 10 for the remaining Buttress and
Cross End on the opposite side. Then, tighten all Screws &
Keps Nuts.
Support Screws
3
/
4
" Wood Screw
325-5106-00
Step 11
(requires Worksurface to be 12" from floor)
Place the Mechanism onto the Worksurface Assembly.
Align the Mechanism Flanges with the predrilled holes
on the Worksurface underside.
Secure the Mechanism to the Worksurface using a total of
twelve Wood Screws.
Align the six holes of the Brake Assembly with those
on the Worksurface. It may be necessary to depress the
Paddle while manipulating the Brake over the predrilled
Worksurface holes.
Secure the Brake Assembly using a total of six Wood Screws.
(12" high surface shown in shaded)
Paddle
Brake
Mechanism Flanges
Wood Screw
