Step 9
(requires Worksurface to be 12” from floor)
Rotate the Caddy Worksurface so the predrilled holes face
upward and the Lip faces the front of the Adjusta Unit.
Slide the Caddy under the Mechanism and align
the three holes located on each end of the Caddy and
Mechanism.
Secure the Caddy using a total of six Wood Screws. Then,
secure the Paddle to the Caddy using four Wood Screws.
NOTE: Make certain the Cable for the Paddle is positioned
underneath the Adjusta Bar.
Anthro
Corporation Technology Furniture
®
10450 SW Manhasset Drive Tualatin, Oregon 97062 1-800-325-3841
anthro.com
Step 2
(uses the 3-Way Wrench)
Unpack the remaining Adjusta Mechanism components
and arrange them as shown at right.
Place one Crossbar end onto the lower Crossbar
Button and Threaded Bolt
(located on each of the Arm
Mechanisms)
. Secure the Crossbar to the Arm Mechanism
using one
5
/
16
” Hex Nut onto the Threaded Bolt.
Repeat for remaining Crossbar end and Arm Mechanism.
5
/
16
” Hex Nut
(included with 225-554x-00)
DETAIL VIEW
Arm Mechanism
Thread-
ed Bolts
5
/
16
” Hex
Nut
Paddle
Brake/Paddle As-
sembly
Arm Mechanism
Crossbar
Lower Crossbar
Button
NOTE: it is very important that you attach the
Crossbar ONLY to the Lower Crossbar Button.
Step 1a
Your Adjusta Mechanism comes unassembled and is
boxed separately inside the Adjusta Unit package.
Begin to assemble the Mechanism by first locating the Adjusta
Crossbar and Brake/Paddle Assembly, position it as shown at
right. Depress the Paddle once to free the Brake Shaft.
Place the Brake Shaft between the two center Crossbar
Flanges. Insert the Post through both center Crossbar
Flanges and Brake Shaft.
Cotter Pin
(included with 225-554x-00)
Center Crossbar Flanges
Cotter Pin
Step 1b
Install the Cotter Pin through the single opening of the
Post to secure into place.
NOTE: included with Adjusta Mechanism is a small bag of
Hardware containing the (1) Post, (1) Cotter Pin, (2) Hex
Nuts, (2) Wood Screws, & (2) Cable Mounts.
Post
(included with 225-554x-00)
Brake Shaft
Brake/Paddle Assembly
Crossbar
Post
3
/
4
” Wood Screw
325-5106-00
Step 10
Install two Caster Inserts into each Base Tube and se-
cure with one Insert Screw per Insert.
Insert one Locking and one Non-Locking Caster into
each Insert of a Base Tube as shown.
Insert two End Caps into the ends of both Base Tubes.
Insert Screw
(with pink threads)
325-5052-00
Locking
Caster
Caster Inserts placed
into the large holes
Leave these two side holes open
Non-Locking
Caster
Paddle
Adjusta Bar
(12” high surface shown shaded)
FAJ30zz/xx3, FAJ36zz/xx3 & FAJ48zz/xx3
Step 11
Attach a Cross Tube to a Base Tube by inserting a fit Bolt
through a Tube Washer, then insert the Bolt through
the
Base Tube and carefully thread into the Cross Tube.
Repeat this procedure for other Cross Tube. Then tighten
all fit Bolts.
fit Tube Washer
225-2050-00 or 225-3522-00
Cross Tube
fit Tube
Washer
(
5
/
16
-18 X 3.5”) fit Bolt
325-5194-00
fit Bolt
Base Assembly
Wood Screw
