manualshive.com logo in svg

ANTAIRA LNX-602N, User Manual, Page: 17 / 39

Share
Download
ANTAIRA LNX-602N User Manual Download Page 17

                                               LNX-602N User’s Manual 

  Antaira Technologies, LLC 

15 

System Location

 

Assign the switch physical location.    The maximum length is 64 

bytes 

System Contact

 

Enter the name of contact person or organization 

Firmware Version

 

Display the switch’s firmware version 

Kernel Version 

Display the kernel software version 

MAC Address

 

Display the unique hardware address assigned by manufacturer 

(default) 

 

 

5.1.2.2  Admin Password 

Change web management login username and password for the management security 

issue 

 

 

Admin Password interface 

 

The following table describes the labels in this screen. 

Label 

Description 

User name

 

Key in the new username (The default is “

admin

”) 

New Password

 

Key in the new password (The default is “

admin

”)   

Confirm password

 

Re-type the new password. 

Apply

 

Click “

Apply

” to activate the configurations. 

 

 

 

5.1.2.3  IP configuration 

You can configure the IP Settings and DHCP client function through IP configuration. 

Summary of Contents for LNX-602N








































Reviews:

No comments