manualshive.com logo in svg

ANTAIRA LMX-1802G-M12-10G-SFP-67 Series, Hardware Manual

Share
Download
ANTAIRA LMX-1802G-M12-10G-SFP-67 Series Hardware Manual Download Page 7

Antaira Technologies - Industrial Ethernet Switches
LMX-1802G-M12-10G-SFP-67 Series - Hardware Manual - v1.0

1.2 Product Software Features

Network Redundancy

-

STP, RSTP, MSTP, ITU-T G.8032 Ethernet Ring Protection Switch (ERPS) for network redundancy

Network Management

-

Web UI based management, SNMP v1/v2/v3, Serial Console

-

QoS, traffic classification QoS, Cos, bandwidth control for Ingress and Egress, broadcast storm control, Diffserv

-

IEEE 802.1q VLAN tagging, port-based VLAN support

-

IGMP snooping v1/v2/v3, IGMP filtering / throttling, IGMP query up to 1024 group

-

Supports IPv4/IPv6, RMON, MIB II, port mirroring, event syslog, DNS, NTP/SNTP, HTTPS, SSH/SSL, TFTP

-

MODBUS TCP for SCADA system integration

Port Configuration

-

Status, statistics, mirroring, rate limiting, event syslog

Event Handling

-

Event notification: Cold/Warm Start, Power Failure, Authentication, SNMP trap and Fault Alarm Relay Output

Storage Upgrade via TFTP and HTTP

Configuration Backup - USB Port

1.3 Package Contents

-

LMX-1802G-M12-10G-SFP-67(-T)

-

Quick Installation Guide

-

2*SFP metal field installable cable end lock

-

Dust cover set

-

SFP removal kit

1.4 Safety Precaution

Attention: If the DC voltage is supplied by an external circuit, please use a protection device on the power supply input.

The industrial Ethernet switch’s hardware specs, ports, cabling information, and wiring installation will be described within

this hardware manual.

Attention: Si la tension CC est fournie par un circuit externe, veuillez utiliser un dispositif de protection sur l'entrée

d'alimentation. Les spécifications matérielles, les ports, les informations de câblage et l'installation du câblage du

commutateur Ethernet industriel seront décrits dans ce manuel d'utilisation.

2

Summary of Contents for LMX-1802G-M12-10G-SFP-67 Series



























Reviews:

No comments

Brands by name

Popular brands

Load more brands