background image

Antaira Technologies - Industrial Ethernet Switches 

LMX-0800 Series Hardware Manual V1.3 

ii 

 

 

 

© Copyright 2018 Antaira Technologies, LLC 

All Rights Reserved 

This document contains information, which is protected by copyright. Reproduction, adaptation or translation 

without prior permission is prohibited, except as allowed under the copyright laws. 

 

Trademark Information 

Antaira is a registered trademark of Antaira Technologies, LLC, Microsoft Windows and the Windows logo are the 

trademarks of Microsoft Corp. NetWare is the registered trademark of Novell Inc. WMM and WPA are the 

registered trademarks of Wi-Fi Alliance. All other brand and product names are trademarks or registered 

trademarks of their respective owners. 

 

Notice: Copyrights © 2018 by Antaira Technologies, LLC. All rights reserved. Reproduction, adaptation, or 

translation without prior permission of Antaira Technologies, LLC is prohibited, except as allowed under the 

copyright laws. 

 
 

Disclaimer 

Antaira Technologies, LLC provides this manual without warranty of any kind, expressed or implied, including but 

not limited to the implied warranties of merchantability and fitness for a particular purpose. Antaira Technologies, 

LLC may make improvements and/or changes to the product and/or specifications of the product described in this 

manual, without prior notice. Antaira Technologies, LLC will not be liable for any technical inaccuracies or 

typographical errors found in this guide. Changes are periodically made to the information contained herein and 

will be incorporated into later versions of the manual. The information contained is subject to change without prior 

notice. 

Summary of Contents for LMX-0800 Series



















Reviews: