background image

Antaira Technologies - Industrial Media Converter 

IMC-C1000-SFP Series User Manual V1.2 

 

 

2.4 LED Indicators 

There are LED light indicators located on the front panel of the industrial Ethernet media 

converter that display the power status and network status. Each LED indicator has a different 

color and has its own specific meaning, see below in Table 2.1

LED 

Color 

Description 

 

Power 

 

 

Green 

On 

Power input 1 or 2 is active 

Off 

Power input 1 or 2 is inactive 

 

LINK/ACT 

(SFP Slot) 

 

 

On 

Connected to network at 100/1000mbps 

Green 

Flashing 

Networking is active 

 

Off 

Not connected to network 

 

RJ45 Port 

(Upper LED) 

 

Green 

 

 

On 

Linked to network at 1000Mbps 

Flashing 

Networking is active 

Off 

Not connected to network 

 

RJ45 Port 

(Lower LED) 

 

Green 

 

 

On 

Linked to network at 10/100Mbps 

Flashing 

Networking is active 

Off 

Not connected to network 

 

 

 

 

2.5 DIP-Switch Setting 

There are 2-set DIP-switch in front panel that can setting for SFP (Link Fault Pass) 

function and SFP transmission rate, see below in Table 2.2 

 

DIP 1 

DIP 2 

Description 

ON 

ON 

LFP Enable and Set SFP to 100Mbps 

ON 

OFF 

LFP Enable and Set SFP to 1000Mbps 

OFF 

ON 

LFP Disable and Set SFP to 100Mbps 

OFF 

OFF 

LFP Disable and Set SFP to 1000Mbps (Default) 

 

 

 

 

Table 2.1 

  LED Indicators for IMC-C1000-SFP Series 

 

Table 2.2 

DIP‐switch setting for 

IMC-C1000-SFP Series 

Summary of Contents for IMC-C1000-SFP Series




















Reviews: