19
2022_001
Caution!
The threads can become damaged if the fuel tank cap is
tightened incorrectly. Make sure that you tighten the fuel tank cap
correctly. Always replace a damaged fuel tank cap.
6
Wait at least 10 minutes for the wick to soak in paraffin before you
operate the product.
3.4 To start the product
1
Fill the fuel tank. Refer to “3.3 To fill fuel” på sid. 18..
Note!
Wait at least 10 minutes for the wick to soak in paraffin before you
operate the product. A dry wick prevents ignition.
2
Put the product is on a stable, level, and heat-resistant surface.
Warning!
Make sure that the location is well-ventilated.
3
Turn the wick adjustment knob clockwise until the wick is at its top
position.
4
Hold the handle on the flue, carefully tilt the flue and ignite the wick
with a match or a lighter.
5
Put the flue back in its vertical position.
6
Wait approximately 15 minutes until the flame becomes stable.
Warning!
Do not go away from the product when it is in operation.
7
Adjust the flame. Refer to “3.5 To adjust the flame” på sid. 19.
3.5 To adjust the flame
The flame is adjusted with the wick adjustment knob. Do the steps that
follow to adjust the flame.
●
If the flame is too low (A), turn the wick adjustment knob clockwise until
the flame is correct. (Figure 4)
●
If the flame is too high (B), turn the wick adjustment knob
counterclockwise until the flame is correct.
3.6 To stop the product
1
Turn the wick adjustment knob counterclockwise until the wick is in
its bottom position. The flame will stop after 3–5 minutes.
Note!
If an emergency occurs, you can push the emergency extinguish
button on the left side of the wick adjustment knob to stop the flame.
2
Make sure that the flame has stopped.
3
Let the product become cool before you move it or do maintenance
on it.
3.7 To remove the fuel from the fuel tank
Warning!
Let the product become cool before you remove fuel
from the fuel tank.
Warning!
Do not remove fuel from the fuel tank indoors.
1
Stop the product. Refer to “3.6 To stop the product” på sid. 19.
2
Remove the fuel tank cap.
3
Drain the fuel into an applicable container.
Warning!
Make sure that you follow local regulations when you
discard the fuel.
4
If it is necessary, clean the fuel tank with 100% pure paraffin.
5
Install the fuel tank cap.
4 Maintenance
4.1 To burn off contaminants from the wick
It is necessary to burn off contaminants from the top of the wick regularly.
To burn off contaminants, do the steps that follow.
1
Make sure that the wick is soaked in paraffin.
2
Make sure that the fuel tank is empty so that the wick cannot absorb
more paraffin.
3
Ignite the wick and let it burn until the flame stops.
4.2 To replace the wick
Warning!
Let the product become cool before you clean it or do
maintenance on it.
Warning!
Only use accessories and parts that are approved by the
manufacturer of the product.
1
Stop the product. Refer to “3.6 To stop the product” på sid. 19.
2
Remove the 3 screws (A) and the safety guard (B). (Figure 5)
3
Remove the flue (C).
4
Remove the 3 wing nuts (D) and the support (E). (Figure 6)
5
Carefully pull out the wick (F) from the wick holder (G). (Figure 7)
6
Make sure that the wick is in the lowest position.
7
Put a new wick in the wick holder. The fiberglass part (H) of the wick
must point upwards.
8
Make sure that the top edge of the fiberglass part is 45–48 mm away
from the top edge of the support. Push the wick outwards from the
inside until it is fixed with the absorber. (Figure 8)
9
Install all parts in the opposite sequence.
Note!
Make sure that the wick moves up when you turn the wick
adjustment knob clockwise and that it moves down when you turn the
wick adjustment knob counterclockwise.