13
And once memory up to full, the camera will show
FULL
, camera
will stop the capturing.
Inserting SD memory card
•
Open the cover, and insert SD memory card in to the SD
card slot completely and in the correct direction as shown
by the top of SD card slot.
•
To remove the SD memory card, depress the SD card and
pull out the card gently.
•
SD cards must be clean (no images from other sources). If
you are using the SD card from other cameras, please
make sure to format the SD card in your computer prior
to use in your camera. New cards are good to use straight
from the package.
FORMAT – Definition
:
When you format a SD memory card, the
operating system erases all information and files on the card.
Then it creates an internal address tables that it later uses to
locate information and files. Formatting also removes all Hidden
System files as well. Basically it cleans your SD memory card just
like if it was brand new.
DO NOT USE
File System type:
“NTFS”
or
“exFAT”
, these formats are not supported.
14
Camera Setup and Program
When the camera switch is first turned in the
A
or
B
or
MANUAL
location, the status display shows the camera status. The
following information is present on this status display.
This camera is equipped with 2 preset and 1 programmable
settings by slide the switch.
Setting the Preset Selection Mode:
NOTE: If you choose one of the Preset settings, your
camera will only function in PIR mode not Time Lapse
mode
•
A (Preset A) -
This bypasses all
user defined settings and uses
the following settings: (PIR
mode / Still image / Resolution:
5MP / Burst: 3P / Time out: 30
seconds).
•
B (Preset B) -
This bypasses all
user defined settings and uses
the following settings: (PIR
mode / Video: 10 seconds video
/ Resolution: 720P / Time out:
30 seconds).
15
Setting the Programmable Selection Mode:
Your camera can be programmed to operation either in PIR
Detection mode or Time Lapse / PIR mode when after
programmed at the SET, and switch slides back to MANUAL.
•
MANUAL
- This allows the user to define what setting the
camera will use.
Passive Infrared Mode
Time-Lapse / PIR Mode
Setting the camera in PIR Mode:
•
Slide the switch to the
SET
position from
OFF
.
•
The status display will show the camera current status.
•
Press the
[M]
button once to enter the Manual
programming mode, the word
PIR
or
TLS
will be blinking.
•
Press the
[UP]
or
[DN]
button to select PIR mode.
•
Press
[OK]
to save your selection.
•
Press
[M]
button to exit.
16
Setting the Image Resolution in PIR mode:
Your camera can be programmed to 3 different image
resolutions: 3 Stars is 12Mp, 2 Stars is 5Mp and 1 Star is 3Mp.
•
Slide the switch to the
SET
position, the status display will
show the camera current status.
•
Press the
[M]
button once enter the Manual
programming mode.
•
The word
PIR
will be blinking, press
[OK]
to confirm the
camera’s operation is PIR detection.
•
Press
[UP]
or
[DN
] button until the word
CAM
is blinking.
•
Press the
[OK]
button ONCE to confirm the camera into
CAM
mode, the
RES
will be blinking.
•
Press
[OK]
then press
[UP]
or
[DN]
button to select the
desired resolution.
•
Press
[OK]
to save your selection, then
burSt
(Burst shoot)
will blinking. Press
[OK]
to enter the burst shoot setting or
press
[M]
button to exit.
Setting the Burst Shoot in PIR mode:
Your camera can be programmed to shoot 1-10 pictures per
triggering.
•
Slide the switch to the
SET
position, the status display will
show the camera current status.
•
Press the
[M]
button once enter the Manual
programming mode.