Anest Iwata ISP-50 Instruction Manual Download Page 16

 

-14- 

Danger of fire and electric shock (refer to chart 1 on page 15) 

 

Install motor protective circuit breaker to protect motor 
If not, it can cause bodily injury due to electric fire or electric shock. 
If you have any questions about the selection of protective devices, contact either the 
dealer who sold it to you or us. 

 

Install motor 

protective circuit 

breaker to protect 

motor 

Danger of short-circuit and electric shock 

 

We recommend an electric wire of larger than 2mm

(more than rated 10A,) cross 

section area for electric wire (including grounding wire.). 
Be careful to avoid voltage drop considering local situation.   

If not, it can cause a short-circuit fire and may result in bodily injury from electric shock. 

 

Be careful about 

wiring 

Danger of short-circuit and electric shock 

 

Insert the connector to the receptacle surely by using an electric wire with an 
appropriate connector. 

If not, it can cause short-circuit fire or bodily injury from electric shock due to looseness 
or disconnection. 

 

Be careful about 

insertion 

Danger of electric shock 

 

Connect grounding wire to electric source. 

If not, it can cause bodily injury from electric shock. 

 

Be sure to ground 

Danger of restart 

 

Be sure to switch off electric source before maintenance or inspection. 
Single-phase motor has a thermal protector. 

Vacuum pump restarts become cool without warning after vacuum pump. 

 

With a thermal 

protector 

CSA Requirement 

 

Thermally protected automatic reset. TYPE TP212. Motor restart without warning after protector trip. 
  Min. circuit ampacity of conductor is 10A 
  Max. branch circuit breaker is 15A 
 

When you use this pump in Europe. 

 

This vacuum pump must be equipped with a main disconnect device in accordance with requirements of 
EN60204-1, clause 5.3.2.

 

It is recommended to use a circuit breaker as main breaker which is suitable for 

isolation according to EN60947-2 and is equipped with an operating handle which is lockable in OFF position 
and complies with the other requirements of EN60204-1, clause 5.3. 

 

 

Summary of Contents for ISP-50



































Reviews: