background image

p17

E1 Single Speed Electric Motor Unit, 12V & 24V 

To Suit Self-Tailing Winch Sizes 58,62

ALL WINCHES

SAFETY NOTICES

DO NOT DISCARD

Failure to observe these precautions could result in serious injury or death.

Read All Safety Notices and Product Manuals

Do not install or operate this winch before reading and fully understanding the contents 
of this Safety Notice Sheet and the Product Manual.

Stay Alert When Operating

Andersen winches are very powerful and have the potential to cause significant damage 
and/or serious injury if used improperly or without due caution and vigilance.

Operators Must be Trained

Help prevent significant damage and/or serious injury by ensuring any person operating a 
winch has a thorough understanding of its proper operation and is aware of the potential 
hazards involved. As a minimum, all winch operators must read and understand this Safety 
Notice Sheet and the Product Manual.

Particular attention is drawn to the following points:

• 

Children and others not qualified to operate an electric winch must be kept at a safe 
distance from the winch and any rigging or fittings that are under load.

• 

Long hair and/or loose clothing must be tied back to avoid being caught in the winch.

• 

In the event of a rope override or other fault, stop the winch and turn off power before 
attempting to resolve the problem.

Avoid Accidental Operation

Remove winch handles and turn off power to the winch when not in use to help avoid 
unsupervised or unintentional operation. Failure to do so could result in significant 
damage and/or serious injury.

Maintenance

Turn off power to the winch before performing any maintenance or service tasks. Failure 
to do so could result in significant damage and/or serious injury.

Lifting Operations

The winch must not be operated with the rope in the self tailer when used in any kind of 
lifting operation. 

Any lifting operations should be conducted by two persons in order to maintain constant 
visual contact with the object being lifted.

Furthermore the self tailer must not be used as a cleat for a rope used to lift or suspend 
any object. The rope must be secured properly by tying off, or leading to a suitable fitting 
such as a cleat or bollard.

Summary of Contents for 58 ST E1



















Reviews: