background image

 

User manual 

Guangzhou Andea Electronics Technology Co., Ltd.                                                          14/15 
http://www.gzandea.com                   

Caution: The user is cautioned that changes or modifications not expressly approved by 
the party responsible for compliance could void the user's authority to operate the 
equipment. 
 
This device complies with Part 15 of the FCC Rules and Industry Canada 
licence-exempt RSS standard(s). Operation is subject to the following two conditions: 
(1) this device may not cause harmful interference, and   
(2) this device must accept any interference received, including interference that may 
cause undesired operation. 
 
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils 
radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :   
(1) l’appareil ne doit pas produire de brouillage, et   
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si 
le brouillage est susceptible d’en compromettre le fonctionnement. 
 
NOTE: This equipment has been tested and found to comply with the limits for a Class 
B  digital  device,  pursuant  to  Part  15  of  the  FCC  Rules.  These  limits  are  designed  to 
provide  reasonable  protection  against  harmful  interference  in  a  residential  installation. 
This  equipment  generates,  uses  and  can  radiate  radio  frequency  energy  and,  if  not 
installed and used in accordance with the instructions,  may  cause harmful interference 
to  radio  communications.  However,  there  is  no  guarantee  that  interference  will  not 
occur in a particular installation.   
If this equipment does cause harmful interference to radio or television reception, which 
can be determined by turning the equipment off and on, the user is encouraged to try to 
correct the interference by one or more of the following measures:   
-- Reorient or relocate the receiving antenna. 
-- Increase the separation between the equipment and receiver.   
--  Connect  the  equipment  into  an  outlet  on  a  circuit  different  from  that  to  which  the 
receiver is connected.   
-- Consult the dealer or an experienced radio/TV technician for help. 

Summary of Contents for RL863



















Reviews: