Chapter 8 : REMOTE CONTROL PROGRAMMER'S GUIDE (continued)
OCTO-QUATTRO™
PAGE 24
8-4. COMMANDS AND RESPONSES TABLE
The following table resumes commands that are recognized as valid and the responses that will be returned to the control
device (on RS-232 port).
VALUE
ASCII
COMMAND
RESPONSE
COMMAND
DESCRIPTION
TYPE
MIN MAX
DESCRIPTION
FRONT PANEL COMMANDS
C CH
Selected
input.
Rd
1 4
c ch
Input
selection.
Rd/Wr
1
4
1 = INPUT #1
2 = INPUT #2
3 = INPUT #3
4 = INPUT #4
o
OBLK
Black screen selection.
Rd/Wr
0
1
1 = black screen
G TAKE
Transition
status.
Rd
0 1
1 = transition in process (automatic reset at the
end of the effect transition).
Z FRZ
FREEZE.
Rd/Wr
0
1
0 = inactive
1 = active.
INPUT COMMANDS
PC
PCH
Input selection for adjustment.
Rd/Wr
0
4
0 = All inputs
1 = INPUT #1
2 = INPUT #2
3 = INPUT #3
4 = INPUT #4
PE
PEN
Input disabling (according to PCH).
Rd/Wr
0
1
0 = Input disable
1 = Input enable
PL
PLD
H sync load selection (according PCH) Rd/Wr
0
1
0 = Hi-Z load
1 = 75
Ω
load
PR PRGB
Input signal type selection. (according
to PCH).
Rd/Wr
0 9
0 = SDTV Composite 1 = SDTV S.VIDEO
2 = SDTV YUV
3 = SDTV RGBS TTL
4 = SDTV RGsB
5 = SDTV RGBS ana.
6 = Computer (SOG)
7 = Computer H&V/C
8 = HDTV
9 = Audio only
PI PSTD
Input standard selection (according to
PCH).
Rd/Wr
0 6
0 = NTSC / PAL / SECAM
1 = NTSC
2 = PAL
3 = NTSC 4.43 60Hz
4 = PAL 4.43 60 Hz
5 = SECAM
6 = Black & White
PP
PPRC
VCR mode (according to PCH).
Rd/Wr
0
1
0 = OFF
1 = ON
OUTPUT COMMANDS
If fast switching =
internal rate
input # X
F OFMT
Output
format
selection. Rd/Wr
0
12
0 = VGA 60 Hz
0 = 640x480L
1 = SVGA 60 Hz
1 = 800x600L
2 = XGA 60 Hz
2 = 1024x768L
3 = SXGA 60 Hz
3 = 1280x1024L
4 = SXGA+ 60Hz
4 = 1400 x1050 L.
5 = VGA 75 Hz
5 = 640x480L
6 = SVGA 75 Hz
6 = 800x600L
7 = XGA 75 Hz
7 = 1024x768L
8 = SXGA 75 Hz
8 = 1280x1024L
9 = D-ILA 4/3
9 = 1365x1024L
10 = D-ILA 16/9
10 = 1365x768L
11 = HDTV 480p
11 = HDTV 480p
12 = HDTV 720p
12 = HDTV 720p.
fm
OSYN
Output sync selection.
Rd/Wr
0
2
0 = H &V
1 = Composite
2 = SOG (Sync On Green).
fs
SCRN
Type of screen selection
Rd/Wr
0
1
0 = screen 4/3
1 = screen 16/9
p OPAT
Test
pattern.
Rd/Wr
0
2
0 = no pattern
1 = centering
2 = color bar
SWITCHING COMMANDS
XR
REFR
Input "reference" selection.
Rd/Wr
0
4
XA REFA
Reference input.
NOTE
: REFA can be different from
REFR, if no sync is connect to the
corresponding input.
Rd
0 4
0 = internal rate
1 = INPUT #1
2 = INPUT #2.
3 = INPUT #3.
4 = INPUT #4.
XI
REFI
Aspect ratio of the reference input.
Rd/Wr
0
2
0 = 4/3
2 = 16/9
NOTE:
Rd/Wr = Read and write command.
Rd
= Read only command.
