manualshive.com logo in svg

Analog Technologies ALDD28V15A401, Quick Start Manual

Share
Download
Analog Technologies ALDD28V15A401 Quick Start Manual Download Page 9

 

1161 Ringwood Ct, #110, San Jose, CA 95131, U. S. A. Tel.: (408) 748-9100, Fax: (408) 770-9187                           www.analogtechnologies.com 

Copyrights 2000-2021, Analog Technologies, Inc. All Rights Reserved. Updated on 3/11/2021   

 

  Email: [email protected]/[email protected]             9     

Analog Technologies 

ALDD28V15A401

Digital High Voltage Constant Current 15A Laser Driver

Or 

 

After the setting is completed, turn the switch to “ON” and 
the controller starts working. 

Press and hold the “Help” button, the display contents are as 
follows: 

 

          

OUTLINE DIMENSIONS  

Dimensions of the DIP package driver are shown in Figure 7. 

 

 

Figure 7. Dimensions of the DIP Package Driver

 

It is highly recommended to lower the solder iron 
temperature to 310°C (590°F) and solder the driver 
manually

, so that the internal contents of the driver would 

not be affected. 

After the soldering, it is also safe to check the laser driver’s 
functionality by using the “dummy laser” before connecting 
a real laser diode as mentioned previously on page 4. 

NOTE: 

The power supplies may have over-shoot voltage 

spikes when they are not connected well with the load or 
when they recover from an over current protection state. 
When that happens, it may exceed the maximum allowed 

input voltage, 27V, of the controller and damage the 
controller permanently. To avoid this from happening, do 
the following: 

1. Connect the controller well with the power supply before 

turning on the power.  

2. Make sure that the power supply has sufficient output 

current. It is suggested that the power supply can 
supply 1.2 to 1.5 times the maximum current the 
controller requires.  

Summary of Contents for ALDD28V15A401











Reviews:

No comments

Brands by name

Popular brands

Load more brands