background image

UG-1461 

ADMV1013-EVALZ

 User Guide

 

Rev. B | Page 18 of 19 

CONFIGURATION OPTIONS 

Table 2. ADMV1013-EVALZ Configuration Options  

Component Function 

Default 

Condition 

1.8 V, 3.3_1013, 3.3 V, 5 V, GND 

Power supplies and ground 

Not applicable 

LON, LOP, IF_I, IF_Q, Q_P, Q_N, I_N, I_P, RF_OUT, VENV_N, 

VENV_P 

RF data and clock local oscillator 
and envelope signal 

Not applicable 

R2 to R4, R6, R8 

33 Ω series resistors for SPI pins 

R2, R3, R4, R6, R8 = 33 Ω (0402) 

R5, R7 

1.1 kΩ series resistors for 
BG_RBIASx pins 

R5, R7 = 1.1 kΩ (0402) 

5V, 3.3V, 3.3V_1013, 1.8V, VCTRL1, VCTRL2, GND1  

Test points 

Not applicable 

R14, R15, R17, R18, R19, R20, R23, XR6 

Shorts or power supply 
decoupling resistors 

R17, R18, R19 = 0 Ω (0603), R15 = 100 kΩ (0402), 
R14, R20, R23 = 0 Ω (0402), XR6 = 80.6 Ω (1206) 

R1, R13, R16, R22, XR2 

Pull-up or pull-down resistors 

XR2, R1, R13, R22 = 10 kΩ (0603), R16 = 100 kΩ 
(0402) 

C2 to C4, C5, C11 to C31, C34 to C42, C43 to C51, C140, 

C141, XC12, XC4 to XC8  

Capacitors provide the 
required decoupling of the 
supply related pins 

XC4, C4, C13, C16, C19, C22, C25, C28, C31, C36, 
C39, C42, C45 = 10 μF (3216), XC12 = 10 μF (0603), 
C5, C44, C46, C48, C49, C51 = 4.7 μF (0603), XC5, 
XC6, XC7, XC8 = 0.1 μF (0402), C43, C47, C50 = 
0.001 μF (0603) C3, C12, C15, C18, C21, C24, C27, 
C30, C35, C38, C41 = 0.01 μF (0402), C2, C11, C14, 
C17, C20, C23, C26, C29, C37, C40 = 100 pF, C24 = 
0.01 μF, C140, C141, XC5 to XC8 = 0.1 μF (0603) 

JP1 to JP4 

IQ path configuration 

Default: JP1 to JP4 = do not install

 

 

IF mode: JP1 to JP4 = do not install 

 

 

IQ mode: JP1 to JP4 = 0 Ω 

C1, R21 

Do not install 

C1, R21 = 0402 

XP1 

Programming header 

Not applicable 

XP2 

Mini USB connector 

Connect the mini USB cable to XP2 to interface 
with the SPI 

S1 

Reset button 

Push the reset button to reset the device. 

USB Red 

LED 

LED is blue when the USB is connected to XP2, 
and the PC and the ADMV1013-EVALZ evaluation 
board are powered on with a 5 V supply 

XU1 Microcontroller 

PIC18F24J50 

U1 Level 

shifter 

FXL4TD245BQX 

U3 to U5 

3.3 V and 1.8 V regulators 

ADM7170

 (U3) = 1.8 V regulator

ADM7172

 

(U5) = 3.3 V regulator

ADM7172

 (U4) = 3.3 V 

regulator fo

ADMV1013

 

U2 

AD5601

 

nano

DAC Not 

applicable 

DUT 

ADMV1013

 device under test 

Not applicable 

PCB PCB, 

ADMV1013-EVALZ

1

 Not 

applicable 

 

1

 The ADMV1013-EVALZ evaluation board material between Layer 1 and Layer 2 is made of 10.7 mil Rogers 4350B LoPRo®. 

Summary of Contents for ADMV1013-EVALZ




















Reviews: