background image

AN231K04-DVLP3 – AnadigmApex Development Board  

 

 

 

 

UM023100-K001h 

Page 1 of 16 

 

Figure 1: AnadigmApex Development Board 

 
 
 
 
 
 

 

Disclaimer 

 
Anadigm reserves the right to make any changes without further notice to any products herein.  Anadigm makes 
no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor 
does Anadigm assume any liability arising out of the application or use of any product or circuit, and specifically 
disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" 
parameters can and do vary in different applications. All operating parameters, including "Typical’s" must be 
validated for each customer application by customer's technical experts. Anadigm does not in this document 
convey any license under its patent rights nor the rights of others. Anadigm software and associated products 
cannot be used except strictly in accordance with an Anadigm software license. The terms of the appropriate 
Anadigm software license shall prevail over the above terms to the extent of any inconsistency. 

 

 
 

© Anadigm

®

, Inc. 2013 

All Rights Reserved

 

Summary of Contents for AnadigmApex

















Reviews: