2. Press
to bring the record up in
the display.
The record could hold up to 20 digits
even though it only displays the last 12.
If a number contains more than 12
digits, you will see turn on.
If it is a private call with no phone number, a blank screen will be shown.
3. Press
again to return to standby.
(You need to subscribe to CID service in order to utilise this feature. Contact
your local telephone company.)
SETTING UP MEMORY DIAL
There are 10 memory locations (
0
to
9
) where you could store phone
numbers. When you enter more than 12 digits, the display will only show the
last 12. However, the memory location could actually store up to 20 digits.
1. Use the number pad to dial the phone
number. The display will show the
digits as you enter them. A 2-second
pause, displayed as “P”, could be
inserted by pressing and holding .
2. If you make a mistake, press to erase one digit at a time, or press
and hold for 2 seconds to clear the entire number and return to
standby.
3. Press
and
is turned on.
4. Press
0
…
9
to store the number.
You’ll hear 2 short beeps when the
number is successfully stored.
will
then turn off.
STORING CID INTO MEMORY DIAL
You can store the last CID record received directly into memory dial.
1. Press
to bring the record up in the display.
2. Press
and
is turned on.
3. Press
0
…
9
to store the number. You’ll hear 2 short beeps when
the number is successfully stored.
PROGRAMMING
You can adjust the ringer melody, flash timing and ringer volume in the
Programming mode.
To enter the Programming mode, simply press and hold until you hear a
beep. will turn on. Press again to exit from Programming mode and
return to standby. If changes have been
made, you’ll hear 2 short beeps as
confirmation.
If you press and hold , you’ll return to
Standby and all the changes you’ve made will be ignored (except ringer
volume).
Ringer Melody & Volume
In Programming mode, you can press
to hear the current melody at
current volume level.
To choose among the 3 melodies, press
1
or
2
or
3
. You will hear the
melody once each time you press the key.
Ringer Melody 1 is the default setting.
To adjust ringer volume among the 6 different levels (including turning the
ringer off), press
repeatedly. The ringer will play once to demonstrate
the volume.
Medium is the default setting.
This setting affects both incoming call ringing and base paging.
Flash Timing
When you are talking on the phone, pressing
will send a flash signal.
You can set the flash timing as either short or long. This is different in
various countries. Check with your local telephone company if you are not
sure.
1. Press
in Programming mode.
2. Press
1
to choose short flash or
2
to choose long flash.
Short flash is the default setting.
10
11
2. Press
to bring the record up in
the display.
The record could hold up to 20 digits
even though it only displays the last 12.
If a number contains more than 12
digits, you will see turn on.
If it is a private call with no phone number, a blank screen will be shown.
3. Press
again to return to standby.
(You need to subscribe to CID service in order to utilise this feature. Contact
your local telephone company.)
SETTING UP MEMORY DIAL
There are 10 memory locations (
0
to
9
) where you could store phone
numbers. When you enter more than 12 digits, the display will only show the
last 12. However, the memory location could actually store up to 20 digits.
1. Use the number pad to dial the phone
number. The display will show the
digits as you enter them. A 2-second
pause, displayed as “P”, could be
inserted by pressing and holding .
2. If you make a mistake, press to erase one digit at a time, or press
and hold for 2 seconds to clear the entire number and return to
standby.
3. Press
and
is turned on.
4. Press
0
…
9
to store the number.
You’ll hear 2 short beeps when the
number is successfully stored.
will
then turn off.
STORING CID INTO MEMORY DIAL
You can store the last CID record received directly into memory dial.
1. Press
to bring the record up in the display.
2. Press
and
is turned on.
3. Press
0
…
9
to store the number. You’ll hear 2 short beeps when
the number is successfully stored.
PROGRAMMING
You can adjust the ringer melody, flash timing and ringer volume in the
Programming mode.
To enter the Programming mode, simply press and hold until you hear a
beep. will turn on. Press again to exit from Programming mode and
return to standby. If changes have been
made, you’ll hear 2 short beeps as
confirmation.
If you press and hold , you’ll return to
Standby and all the changes you’ve made will be ignored (except ringer
volume).
Ringer Melody & Volume
In Programming mode, you can press
to hear the current melody at
current volume level.
To choose among the 3 melodies, press
1
or
2
or
3
. You will hear the
melody once each time you press the key.
Ringer Melody 1 is the default setting.
To adjust ringer volume among the 6 different levels (including turning the
ringer off), press
repeatedly. The ringer will play once to demonstrate
the volume.
Medium is the default setting.
This setting affects both incoming call ringing and base paging.
Flash Timing
When you are talking on the phone, pressing
will send a flash signal.
You can set the flash timing as either short or long. This is different in
various countries. Check with your local telephone company if you are not
sure.
1. Press
in Programming mode.
2. Press
1
to choose short flash or
2
to choose long flash.
Short flash is the default setting.
10
11
