Basic Steps to Install
1. Align the base unit with the base stand and snap into place. (To remove,
pull the stand from the front.)
2. Connect the output plug of the mains adapter to the
socket on
the bottom of the base unit and the mains adapter to the wall mains
supply.
3. Place the 2 AAA batteries, observing their polarities, into the battery
compartment on the handset.
4. Slide the battery door firmly into place.
5. Connect the telephone lead to the
socket on the bottom of the base
unit and to the wall phone socket.
6. Place the handset on the base unit and let the batteries charge for a full
14 hours before using.
Caution
Use only the mains adapter supplied with this telephone. Incorrect adapter
polarity or voltage can seriously damage the unit.
Adapter Model No.:
Input: 230 VAC 50 Hz
Output: 7 VDC 300 mA and 7 VAC 150 mA
Caution
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT
TYPE. Refer to the original type supplied with this telephone. NiMH
batteries must be disposed of in accordance with applicable waste disposal
regulations.
Charging the Handset
Place the handset on the base cradle to recharge the handset batteries. The
charge LED will be steadily lit.
When the low battery icon
is displayed, the batteries need recharging.
When you are talking on the phone, you’ll also hear a warning beep.
BASIC OPERATIONS
During Standby
When the phone is not in use, the LCD
displays the handset number and all the
applicable icons (e.g. Low Battery, Ringer
Off).
To answer an incoming call …
When there is an incoming call, the phone
will ring and the CID record, if any, will be
displayed. flashes according to the
ringing cadence. turns on when there is
CID record.
turns on if the phone number contains more than 12 digits. In this case,
only the last 12 digits are displayed.
Before answering the call, you can press
to adjust the ringing volume
to a desired level.
“------------” indicates that the call is private
and the phone number is not available.
1. Press
to answer the call. is
turned on.
2. Press
again or place the handset
on the base cradle to disconnect.
To make a call…
Your phone allows you to dial out a phone number in various ways. In each
case, will turn on when the phone number contains more than 12 digits.
Using Traditional Dialing
1. Press
and wait for the dial tone.
is turned on.
2. Use the number pad to dial the phone
number. The display shows the digits
as you enter them.
6
7
Basic Steps to Install
1. Align the base unit with the base stand and snap into place. (To remove,
pull the stand from the front.)
2. Connect the output plug of the mains adapter to the
socket on
the bottom of the base unit and the mains adapter to the wall mains
supply.
3. Place the 2 AAA batteries, observing their polarities, into the battery
compartment on the handset.
4. Slide the battery door firmly into place.
5. Connect the telephone lead to the
socket on the bottom of the base
unit and to the wall phone socket.
6. Place the handset on the base unit and let the batteries charge for a full
14 hours before using.
Caution
Use only the mains adapter supplied with this telephone. Incorrect adapter
polarity or voltage can seriously damage the unit.
Adapter Model No.:
Input: 230 VAC 50 Hz
Output: 7 VDC 300 mA and 7 VAC 150 mA
Caution
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT
TYPE. Refer to the original type supplied with this telephone. NiMH
batteries must be disposed of in accordance with applicable waste disposal
regulations.
Charging the Handset
Place the handset on the base cradle to recharge the handset batteries. The
charge LED will be steadily lit.
When the low battery icon
is displayed, the batteries need recharging.
When you are talking on the phone, you’ll also hear a warning beep.
BASIC OPERATIONS
During Standby
When the phone is not in use, the LCD
displays the handset number and all the
applicable icons (e.g. Low Battery, Ringer
Off).
To answer an incoming call …
When there is an incoming call, the phone
will ring and the CID record, if any, will be
displayed. flashes according to the
ringing cadence. turns on when there is
CID record.
turns on if the phone number contains more than 12 digits. In this case,
only the last 12 digits are displayed.
Before answering the call, you can press
to adjust the ringing volume
to a desired level.
“------------” indicates that the call is private
and the phone number is not available.
1. Press
to answer the call. is
turned on.
2. Press
again or place the handset
on the base cradle to disconnect.
To make a call…
Your phone allows you to dial out a phone number in various ways. In each
case, will turn on when the phone number contains more than 12 digits.
Using Traditional Dialing
1. Press
and wait for the dial tone.
is turned on.
2. Use the number pad to dial the phone
number. The display shows the digits
as you enter them.
6
7
