![background image](http://html.mh-extra.com/html/amx/nxa-smt43x/nxa-smt43x_installation-manual_2938712003.webp)
For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).
1/11
©2011 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX.
AMX reserves the right to alter specifications without notice at any time.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com
93-2262-16
REV: A
Installing the NXD-430/435 Display Into the NXA-SMT43X
1.
Pull enough Ethernet cable through the wall or conduit to allow a connection to the
touch panel. Connect the Ethernet cable to the touch panel display.
NOTE:
Do NOT apply power at this time.
2.
The interior of the surface mount box has two slots in the top (FIG. 4). Insert the two
tabs at the top of the touch panel display into those slots, and pivot the bottom of the
display into the surface mount box.
3.
At the bottom of the display are two screw holes. Insert the two included cap screws
into the holes and carefully tighten. Do not use excessive torque on these screws, as
this may damage the display circuit board.
Attaching the Bezel to the Touch Panel Display
When installing an NXD-430/435 into an NXA-SMT43X, the front bezel is installed differently
than in a typical installation.
1.
With an NXD-435, carefully connect the ribbon cable from the touch panel display to
the bezel.
2.
Attach the bezel to the surface mount box by placing the assembly tabs on top of the
surface mount box into the pockets on the top of the bezel (FIG. 5).
3.
Press the lower portion of the bezel toward the display until it snaps into place.
Attaching the Cover to the Surface Mount Box
1.
Slide the cover over the front of the surface mount box (FIG. 6). Make sure that the slot
for the side conduit knockout is on the right bottom of the cover, as it faces toward you.
2.
Insert the 2 supplied painted white Torx-head screws into the screw holes at the
bottom of the cover and tighten.
3.
Connect the Ethernet to the Master and verify that the touch panel receives power and
data.
.
NXA-SMT43X Wall Cover Plate
The NXA-SMT43X wall cover plate (
53-2266-02
) is a disposable cover shipped with the
NXA-SMT43X. In situations where the NXA-SMT43X box is installed before the touch panel
assembly, the cover protects the interior of the box from falling dust. When the touch panel is
installed, the cover should be removed and disposed of in an environmentally friendly
manner.
To install the wall cover plate:
1.
Install the mounting plate and surface mount box to the wall (FIG. 2).
2.
Slide the wall cover plate over the surface mount box and secure it with the two
included #8 screws (
80-0146-02
3.
When ready to install the touch panel, remove the wall cover plate (FIG. 8), and install
the rest of the NXA-SMT43X as necessary.
FIG. 4
Inserting the NXD-430/435 display into the NXA-SMT43X
FIG. 5
Attaching the bezel to the touch panel display
Screws
Surface mount
box slots
Assembly tabs
for bezel
Assembly slot
for snaps on bezel
FIG. 6
Attaching the cover to the surface mount box
FIG. 7
Installing the NXA-SMT43X wall cover plate to the surface mount box
FIG. 8
NXA-SMT43X with installed wall cover plate
Torx-head screws
Surface Mount Box
NXA-SMT43X
Wall Cover Plate
#8 screw
#8 screw