Installation Guide
NXA-ENET8-2POE
Gigabit Ethernet Layer 2 PoE Switch
Overview
The NXA-ENET8-2POE (
FG2178-63
) is a Gigabit Ethernet Layer 2 PoE switch with 8 10/
100/1000BASE-T ports, and 2 Small Form Factor Pluggable (SFP) transceiver slots, (see
Figure 1, Ports 9-10).
The NXA-ENET8-2POE also includes an SNMP-based management agent, which provides
in-band access for managing the switch.
The NXA-ENET8-2POE provides a broad range of powerful features for Layer 2 switching,
delivering reliability and consistent performance for your network traffic. They bring order to
poorly performing networks by segregating them into separate broadcast domains with IEEE
802.1Q compliant VLANs, and empower multimedia applications with multicast switching
and CoS services.
Hardware Specifications
Installation
Selecting a Site
The site should:
•
Be at the center of all the devices you want to link and near a power outlet.
•
Be able to maintain its temperature within 0° to 50°C (32° to 122°F) and its humidity
within 10% to 90%, non-condensing
•
Provide adequate space (approximately two inches) on all sides for proper air flow
•
Be accessible for installing, cabling and maintaining the devices
•
Allow the status LEDs to be clearly visible
Make sure twisted-pair cable is always routed away from power lines, fluorescent lighting
fixtures and other sources of electrical interference, such as radios and transmitters.
Make sure that the unit is connected to a separate grounded power outlet that provides 100
to 240 VAC, 50 to 60 Hz, is within 2 m (6.6 feet) of each device and is powered from an
independent circuit breaker. As with any equipment, using a filter or surge suppressor is
recommended.
Ethernet Cabling
To ensure proper operation when installing the NXA-ENET8-2POE into a network, make sure
that the current cables are suitable for 10BASE-T, 100BASE-TX, or 1000BASE-T operation.
Check the following criteria against the current installation of your network:
•
Cable type: Un-shielded twisted pair (UTP) or shielded twisted pair (STP) cables with
RJ-45 connectors; Category 3 or better for 10BASE-T, Category 5 or better for
100BASE-TX, and Category 5, 5e, or 6 for 1000BASE-T.
•
Protection from radio frequency interference emissions
•
Electrical surge suppression
•
Separation of electrical wires (switch related or other) and electromagnetic fields from
data based network wiring
•
Safe connections with no damaged cables, connectors or shields
Mounting
The NXA-ENET8-2POE can be mounted in a standard 19-inch equipment rack or on a
desktop or shelf. Mounting instructions for each type of site follow (see reverse).
Rack Mounting
Before rack mounting the NXA-ENET8-2POE, pay particular attention to the following
factors:
•
Temperature
: Check that the rack environment temperature (within a rack assembly)
is within the specified operating temperature range (see the
Specifications
table).
•
Mechanical
Loading
: Do not place any equipment on top of the rack-mounted unit.
•
Circuit
Overloading
: Be sure that the supply circuit to the rack assembly is not over-
loaded.
FIG. 1
NXA-ENET8-2POE (front and rear panels)
NXA-ENET8-2POE Hardware Specifications
Features
• IGMP snooping v1/v2/v3
• IPv6 support
• 802.1Q VLAN support
• 802.1X Port and MAC-based authentication
• IEEE 802.1p CoS support
• In-band Management: Web, or SNMP manager
Performance
• Switching Capability: 20 Gbps (aggregate bandwidth)
• Packet Buffer Size: 1 MB
• Switching Database: 8K MAC Address Table
• Flash: 8 MB
• Forwarding Mode: Store-and-forward
• Throughput: Wire speed
• Flow Control: Full Duplex: IEEE 802.3x, Half Duplex: Back
pressure
Standards
• IEEE 802.3-2005
• Ethernet, Fast Ethernet, Gigabit Ethernet
• Full-duplex flow control
• Link Aggregation Control Protocol
• IEEE802.3at Power-over-Ethernet
• ISO/IEC 8802-3
Physical Ports:
• 8 10/100/1000BASE-T RJ-45 PoE ports
• 2 Gigabit Ethernet SFP slots (dual speed 100/1000BASE-X)
LEDs
• System: PWR, DIAG, PoE
• Port: Status (Link, Speed, Activity)
Network Interface
Ports 1-8:
RJ-45 connector, auto MDI/MDI-X:
• 10BASE-T: RJ-45 (100-ohm, UTP cable; Cat 3 or better)
• 100BASE-TX: RJ-45 (100-ohm, UTP cable; Cat 5 or better)
• 1000BASE-T: RJ-45 (100-ohm, UTP cable; Cat 5, 5e or better)
Maximum cable length - 100 m (328 ft)
Ports 9-10:
SFP transceiver slots:
100BASE-FX, 1000BASE-SX,1000BASE-LX, 1000BASE-LH,
1000BASE-T
The maximum length for fiber optic cable operating at Gigabit
speed will depend on the fiber type.
See the
1000 MBPS Gigabit Ethernet Collision Domain
section in
the
NXA-ENET8-2POE Operation/Reference Guide
for details.
PoE (IEEE 802.3at Power over Ethernet)
Max output power:
Up to 30 W per port, within the total PoE power budget
Total PoE budget:
75 W
Voltage:
Maximum current: 1.7A
PoE Output Voltage:
48 V DC
Reset Button
10/100/1000 Mbps
1000BASE-T/SFP Ports (9-10)
Grounding Point
Power Inlet
SPF Port Status LEDs (ports 9-10 Link/Activity/Speed)
Power Status LED
Diagnostics Status LED
PoE Status LEDs (ports 1 - 8)
Ethernet Port Status LEDs (ports 1-8)
(Link/Activity/Speed)
RJ45 PoE Ports (1-8)
NXA-ENET8-2POE Hardware Specifications (Cont.)
Power Requirements:
Power Consumption
• 75 Watts for PoE power (Max from AC inlet)
• 20 Watts for system power
Voltage:
• 100-240V
• 50-60Hz
• 1.5 A
Current:
• 1.5 A @ 110 VAC
• 0.75 A @ 220 VAC
Power Supply
• AC Power: 100 to 240 V, 50-60 Hz, 0.7A
• Power Supply: Internal, auto-ranging transformer:
100 to 240 VAC, 50 to 60 Hz
• Power Consumption: 100 Watts
• Maximum Current: 1.7A @ 100 VAC
Physical
Size (W x D x H)
33 x 20.4 x 4.3 cm (12.99 x 8.03 x 1.69 in.)
Weight
2.2 kg (4.85 lbs)
Environmental
Temperature:
• Standard Operating: 0°C to 50°C (32°F to 122°F)
• Non-Operating (Storage): -40°C to 70°C (-40°F to 158°F)
Humidity
10% to 90% (non-condensing)
Compliances
• W FCC Part 15 Class A
• IC CISPR 22 Class A
• CE EN 55022 Class A and EN 55024
• LVD EN 60950-1
• CB Scheme IEC 60950-1
• CSA 22.2 NO 60950-1
Included Accessories
• Four adhesive foot pads
• Grounding screw
• Two brackets and eight screws
• Power Cord
Other AMX Equipment: • NXA-WAP1000 - 802.11a/b/g/n Wireless Access Point
(FG2255-51/53)
• NXA-WAPZD1100 - Wireless LAN ZoneDirector (FG2255-75,
FG2255-54K – 60K)
