For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).
12/13
©2013 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX.
AMX reserves the right to alter specifications without notice at any time.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com
93-0553-13
REV: A
2. Remove the End Cap and Existing Modules
Remove the End Cap as well as existing modules (as necessary, depending on how
you want the modules arranged) from one end of the HPX base assembly.
1.
Remove the (silver) pivot screw and pivot pawl assembly in the center of the
End Cap (FIG. 5).
2.
Remove the six (black) sheet metal screws that secure the End Cap to the HPX
assembly (locations circled in red below).
3.
Gently slide the End Cap out of the HPX base assembly.
3. Insert the Dual USB Module into the HPX Base
1.
Orient the module relative to the HPX base assembly so that the Module’s
faceplate is facing up, towards the mounting surface (FIG. 6).
2.
Align the Mounting Notches on the module with the Mounting Rails on the HPX
base.
Note: Module faceplates are notched in a “tongue and groove" type fashion to ensure
that all modules are oriented correctly in the HPX. Note the orientation of the notched
faceplate on each module before sliding the module(s) into the HPX assembly.
3.
Slide the module into position.
4.
Install any remaining modules into the HPX base.
4. Re-Install the End-Cap
Caution: Do not use a high-powered torque screw driver. Over-tightening these
screws can damage the product.
1.
Align the Mounting Notches on the End Cap with the Mounting Rails on the HPX
base.
2.
Slide the End Cap into the HPX base until it is fully inserted against the end of
the base assembly.
3.
Secure the End Cap with the six (black) sheet metal screws (removed in
Step 2 - 2; see FIG. 5).
4.
Replace the (silver) pivot screw and pivot pawl assembly (removed in Step 2 - 1,
see FIG. 5) in the center of the End Cap.
5. Mount the HPX into the Mounting Surface
Caution: Do not use a high-powered torque screw driver. Over-tightening these
screws can damage the product.
Note: For detailed instructions on installing the HPX base assembly, refer to the
HPX-600/900/1200 Installation Guide (available online at www.amx.com).
1.
Carefully insert the HPX base into the cutout in the mounting surface.
2.
Tighten the four mounting screws (loosened in Step 1, see FIG. 4) located inside
and at each end of the HPX base assembly, to rotate the retaining tabs into
locking position under the mounting surface.
3.
Replace any cable ties that were removed in Step 1.
Connecting the USB Module to the PSU2.1 USB Power Supply
Plug the two USB cables from the USB module into the USB ports on the included
PSU2.1 Power Supply (see FIG. 2).
USB Power Supply Installation
Install the Appropriate Power Adapter
The PSU2.1 USB Power Supply comes with Power Adapters to accommodate various
wall outlet types. Select the Power Adapter that is appropriate for your locale and
mount it on the PSU2.1:
1.
Align the mounting slots on the Power Adapter with the metal prongs on the
PSU2.1
2.
Slide the adapter into place, until it “clicks” into it’s secure position (FIG. 7):
3.
Plug the power supply (with Power Adapter installed) to a wall outlet.
Note that the (blue) Power Status LEDs light to indicate that the PSU2.1 is
receiving power.
4.
Plug both USB cables from the USB Module into the PSU2.1.
Note: The PSU2.1 USB Power Supply is also available to purchase separately from
AMX (FG423-25).
Additional Documentation
Refer to the
Products > Architectural Connectivity
catalog page on
www.amx.com
(
Dealer Site
) for additional product documentation.
FIG. 5
HPX Base Assembly (shown mounted) - Mounting/Pivot Screw Locations
FIG. 6
Installing the HPX-N102-USB-PC Module
HPX Base Assembly
Mounting Surface
End Cap
Interlocking tabs
PSU2.1 Included Power Adapters
NEMA 1-15
BS 1363
CEE 7/16 Europlug
AS/NZS 3112
FIG. 7
Installing a Power Adapter on the PSU2.1
