Quick Start Guide
Mio Modero DMS Pinnacle
Touch Keypad
Overview
The Mio Modero DMS Pinnacle device family provides a wide range of control
capabilities in the form of user specified touch keypads that are functional yet
recherché.
Mio Modero DMS Pinnacle keypad are equipped with an LCD touch slider that allows
you to navigate the dynamic menu system displayed in the LCD touch keypad area.
The slider works by running either your finger or a stylus up and down.
Specifications
Dynamic Menu System
Using the KeypadBuilder application available for download from
www.amx.com
, the
Mio Modero DMS Pinnacle is programmed with a Dynamic Menu System (DMS) that
is navigated via the slider and LCD touch keypad area. See the
KeypadBuilder
Instruction Manual
for more information on programming Mio Modero DMS Pinnacle
devices.
Installation
Note:
To avoid any damage to the electronic component, installation must be
performed in an ESD safe environment.
The installation section addresses the mounting and wiring of the Mio Modero DMS
Pinnacle. After you have completed the installation you must consult
Necessary
Device Setup
.
Rear Components
The rear components of the Mio Modero DMS Pinnacle (FIG. 2) are as follows:
Connections and Wiring
The Mio Modero DMS Pinnacle device is powered either via 12VDC or Power over
Ethernet (PoE). If both the 12 VDC and PoE power sources are connected, by default
the device draws power from the 12 VDC. If the 12 VDC source is disconnected, the
PoE automatically supplies power after a device reboot.
Note:
Do not connect power to the Mio Modero DMS Pinnacle until the wiring is
complete.
Preparing captive wires for the 2-pin 3.5 mm mini-Phoenix connector
You will need a wire stripper, and flat-blade screwdriver to prepare and connect the
captive wires.
1.
Strip 0.25 inch (6.35 mm) of wire insulation off all wires.
2.
Insert each wire into the appropriate opening on the connector according to the
wiring diagrams and connector types described in this section.
3.
Turn the screws clockwise to secure the wires in the connector.
Note:
Do not over-torque the screws; doing so can bend the seating pins and damage
the connector.
Using the PSN NetLinx connector for power
The PWR and GND cable from the 12 VDC power supply must be connected to the
corresponding location on the 2-pin 3.5 mm mini-Phoenix connector (See the
KeypadBuilder Instruction Manual
for an illustration).
1.
Insert the PWR and GND wires on the terminal end of a PSN 2-pin 3.5 mm
mini-Phoenix cable. Match the wiring locations of the +/- on both the power
supply and the terminal connector.
2.
Tighten the clamp to secure the two wires.
3.
Verify the connection of the 2-pin 3.5 mm mini-Phoenix to the power supply.
Using the Ethernet port for power
Connect your CAT5/CAT6 Ethernet cable to the port shown in FIG. 2. (See the
Mio
Modero DMS & Mio Modero DMS Pinnacle
instruction manual for an illustration and
cable pinouts).
Mounting Procedures
FIG. 3 shows the mounting dimensions for the Mio Modero DMS Pinnacle. Reference
these measurements when planning and installing the device. Consult the
Mio Modero
DMS & Mio Modero DMS Pinnacle
instruction manual for other installation methods.
FIG. 1
Mio Modero DMS Pinnacle Device Family
Mio Modero DMS Pinnacle (FG2408-02XX) Specifications
Power 12 VDC / PoE:
Maximum power consumption (PoE):
• 5.5 Watts
Maximum startup (rush) current (PoE):
• 150 mA @ 50 VDC
Maximum continuous current (PoE):
• 100 mA @ 50 VDC
Maximum power consumption (DC):
• 5.0 Watts
Maximum startup (rush) current (DC):
• 525 mA @ 13.5 VDC
Maximum continuous current (DC):
• 350 mA @ 13.5 VDC
Front Panel Components:
• LCD Touchpad
• Touch-Slider
Rear Panel Connectors:
• Ethernet Port (PoE)
• 2-pin 3.5 mm mini-Phoenix (female) connector
Dimensions (HWD):
• 4.50 (114.3 mm) x 3.50 (91.4 mm) x 2.88 (73 mm)
Supported Fonts:
Only True Type Fonts
Weight (range):
• Device - .45 lbs (.20 kg)
• Back box - .20 lbs (.09 kg)
Operating Environment:
• Operating Temperature: 0° to 40° C (32° to 104° F)
• Storage Temperature: -10° to 60° C (14° to 140° F)
Mounting:
The Mio Modero DMS Pinnacle is installed in one of two
ways:
• 4 screws for hard surface mounting
• 2 expansion clips for pressure mounting
Available Color Schemes:
Black (BL), White (WH), Beige (BG), Almond (AL),
Brown (BR), Gray (GR), Ivory (IV), Light Almond (LA),
Taupe (TP), Gold (GL), Silver (SL)
Included Accessories:
• 2-pin 3.5 mm mini-Phoenix connector (
41-5025
)
• Mounting kit (
KA2250-01
)
Touch Slider
Menu Header
Touch-select
menu items
FIG. 2
Mio Modero DMS Pinnacle Rear Components
2-pin
3.5 mm
(female)
Ethernet Port
Board Orientation
Notch
This notch coincides
with an indentation in
the back box. The
notch is always on the
left.
(Front View)
(PoE)
connector
mini-Phoenix
Device Removal Notch
This notch coincides with
a metal tab on the back box.
The metal tab prevents damage
to installation surfaces.
