background image

iii

 Alero 8-Channel Microphone Mixer Instruction Manual

FCC AND CANADA EMC COMPLIANCE INFORMATION:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may

cause undesired operation.

NOTE:

 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits 

are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate 

radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. 

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or 

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or 

more of the following measures:



Reorient or relocate the receiving antenna.



Increase the separation between the equipment and receiver.



Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.



Consult the dealer or an experienced radio/TV technician for help.

Approved under the verification provision of FCC Part 15 as a Class B Digital Device.

CAN ICES-3 (B)/NMB-3(B)
EU COMPLIANCE INFORMATION:

Eligible to bear the CE mark; Conforms to European Union Low Voltage Directive 2006/95/EC; European Union EMC Directive 2004/108/EC; European 
Union Restriction of Hazardous Substances Recast (RoHS2) Directive 2011/65/EU; European Union WEEE (recast) Directive 2012/19/EU; 

You may obtain a free copy of the Declaration of Conformity by visiting 

http://www.amx.com/techcenter/certifications.asp

WEEE NOTICE 

ESD Warning: The icon to the left indicates text regarding potential danger associated with the discharge of static 

electricity from an outside source (such as human hands) into an integrated circuit, often resulting in damage to the 

circuit.

WARNING

To reduce the risk of fire or electrical shock, do not expose this apparatus to rain or moisture.

WARNING

No naked flame sources - such as candles - should be placed on the product.

WARNING

Equipment shall be connected to a MAINS socket outlet with a protective earthing connection.

WARNING

This product is intended to be operated ONLY from the voltages listed on the back panel or the recommended, or included, 

power supply of the product. Operation from other voltages other than those indicated may cause irreversible damage to the 

product and void the products warranty. The use of AC Plug Adapters is cautioned because it can allow the product to be 

plugged into voltages in which the product was not designed to operate. If the product is equipped with a detachable power 

cord, use only the type provided with your product or by your local distributor and/or retailer. If you are unsure of the correct 

operational voltage, please contact your local distributor and/or retailer.

WARNING

Do Not Open! Risk of Electrical Shock. Voltages in this equipment 

are hazardous to life. No user-serviceable parts inside. Refer all servicing to 
qualified service personnel.

 

CAUTION

Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this 
device.

This appliance is labeled in accordance with European Directive 2012/19/EU concerning waste of electrical and 

electronic equipment (WEEE). This label indicates that this product should not be disposed of with household waste. It 

should be deposited at an appropriate facility to enable recovery and recycling. 

Summary of Contents for ALR-AEC-8 ALERO























Reviews: