![AMW 100 Installation Manual Download Page 29](http://html.mh-extra.com/html/amw/100/100_installation-manual_2937381029.webp)
AMW 12_00
25
S
S
A
A
F
F
E
E
T
T
Y
Y
R
R
E
E
G
G
U
U
L
L
A
A
T
T
I
I
O
O
N
N
S
S
FROST
The unit must be protected against frost. When currentless, the LPHW can freeze.
PROTECTION VOLUME
All units must be placed outside the protection volume as specified in European standards.
U
U
N
N
I
I
T
T
S
S
T
T
H
H
A
A
T
T
A
A
R
R
E
E
P
P
L
L
A
A
C
C
E
E
D
D
I
I
N
N
S
S
I
I
D
D
E
E
T
T
H
H
E
E
P
P
R
R
O
O
T
T
E
E
C
C
T
T
I
I
O
O
N
N
V
V
O
O
L
L
U
U
M
M
E
E
,
,
M
M
U
U
S
S
T
T
B
B
E
E
C
C
O
O
N
N
N
N
E
E
C
C
T
T
E
E
D
D
T
T
O
O
A
A
N
N
I
I
S
S
O
O
L
L
A
A
T
T
I
I
N
N
G
G
T
T
R
R
A
A
N
N
S
S
F
F
O
O
R
R
M
M
E
E
R
R
O
O
R
R
B
B
E
E
D
D
O
O
U
U
B
B
L
L
E
E
I
I
N
N
S
S
U
U
L
L
A
A
T
T
E
E
D
D
.
.
Hygrostats, thermostats and similar connected to the circuit board (24 VDC) are the ultra-low safety voltage type
and can be placed inside the protection volume.
AIR FLOW
AMW units cannot be equipped with ducts: the fan can never absorb the pressure loss in the ducts.
INTAKE AND OUTLET
The intake and outlet grids should always be clear. Blocked grids can lead to a reduction in air flow which causes
the unit to switch into safety mode where it can only be restarted after manual reset.
M
M
A
A
I
I
N
N
T
T
E
E
N
N
A
A
N
N
C
C
E
E
FILTERS
All types are equipped with air filters. On start up a lot of building dust can be drawn in, so it is recommended that
after a few weeks from starting up a new installation, the filters be checked and cleaned if necessary.
After a time, the period between two checks can be extended but it is still recommended to check the filters at least
twice a year.
A
A
L
L
W
W
A
A
Y
Y
S
S
D
D
I
I
S
S
C
C
O
O
N
N
N
N
E
E
C
C
T
T
T
T
H
H
E
E
U
U
N
N
I
I
T
T
B
B
E
E
F
F
O
O
R
R
E
E
R
R
E
E
P
P
L
L
A
A
C
C
I
I
N
N
G
G
T
T
H
H
E
E
F
F
I
I
L
L
T
T
E
E
R
R
The filter is accessible by removing the back.
Unscrew the 6 screws of the back panel.
The back panel can now be removed.
Lift the filter and remove it.
Replace the cleaned or new filter in its position and screw the back panel down.
HOUSING
The housing can be cleaned regularly with a detergent without aggressive agents.
Summary of Contents for 100
