manualshive.com logo in svg

Amsco Century Series, Routine Maintenance

Share
Download
Amsco Century Series Routine Maintenance Download Page 40

5-15

Troubleshooting

Routine Maintenance

129367-410

Alarm

Description

Screen with Operator Instructions

Reference Drain

Deviation Alarm

STATUS

PAPER

PRINT

FEED

SILENCE

SERVICE

ALARM

HELP

STATUS..

ALARM!  REFERENCE

249

DRAIN DEVIATION ALARM

CHAMBER:

000.0 C

00.0 psig

REFER:

000.0 C

STERILIZER WILL:

•

AUTOMATICALLY TRY TO COMPLETE CYCLE

OPERATOR INSTRUCTIONS:

1. SILENCE ALARM

2. CALL SERVICE

Occurs if chamber
temperature varies
±2°F (1°C) from the
reference temperature.
(Lab/Sci program option
only.)

Screen with Service Instructions

Screen with Operator Instructions

→

DEVIATION BETWEEN REFERENCE AND

CHAMBER PROBE IS MORE THAN 1 C.

CAUSES AND CORRECTION:

1.

LOOSE CONNECTION IN PROBE WIRING

→

REPAIR

2.

CHAMBER/REFERENCE PROBE FAILED

→

REPLACE

→

RECALIBRATE

3.

CONTROL OUT OF CALIBRATION

→

RECALIBRATE (CONTACT QUALIFIED

SERVICE PERSON)

4.

MAIN CONTROL FAILURE

→

CHECK CONTROL BOARD POWER STATUS

LEDs

→

REPLACE 146656-185 CONTROL BOARD

→

REPLACE 146659-003 ANALOG BOARD

→

RECALIBRATE

STATUS..

SERVICE INFORMATION:

250

REFERENCE/CHAMBER DEVIATION

PAPER

CLEAR

EXIT

FEED

ALARM

Waste Temperature

Probe Failure

Occurs if waste line
temperature reading is
outside the normal range
of 32-293°F (0-145°C).

STATUS

PAPER

PRINT

FEED

SILENCE

SERVICE

ALARM

HELP

STATUS..

ALARM!  WASTE

215

TEMPERATURE PROBE FAILURE

CHAMBER:

000.0 C

00.0 psig

WASTE:

000.0 C

STERILIZER WILL:

•

PREVENT NEW CYCLE FROM BEING

STARTED UNTIL ALARM IS CLEARED

OPERATOR INSTRUCTIONS:

1. SILENCE ALARM

2. CALL SERVICE

Summary of Contents for Century Series



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands