1
2
3
Preface
Safety Warnings
Overview
Package contents
This user's manual describes the installation, commissioning and maintenance of
GSM/CDMA wide band consumer boosters of single band.
Please do read user manual carefully before installing and maintaining the
booster.
The information in this manual is subject to change without prior notice.
Opinions are welcomed about the manual improvement.
Booster should follow system requirement of communication equipment,
assure good grounding and lightning protection.
The power supply voltage of booster should meet the standards of security
requirement; any operation shall be carried out only after cutting off power in
advance. Only the professional is authorized for the operation.
Do not dismantle machine, maintain or displace accessories by yourself,
because in this way, the equipment may be damaged and you may even get
an electric shock.
Do not open the booster, touch the module of booster, or open the cover of
module to touch the electronic component. The components will be damaged
due to electrostatic.
Please keep away from heating-equipment, because the booster will
dissipate heat during working. And do not cover booster with anything that
influences heat-dissipation.
!
!
!
Users must follow the below principles
：
CDMA or GSM single band consumer booster is designed to help mobile users
amplify weak signals of 2G, 3G. They are bi-directional amplifiers.
The donor antenna receives the signals from the cell tower, and transmits to the
signal booster, the signal booster amplifies them and then the indoor antenna will
retransmit to your mobile device.
Vice Versa, the signals produced by your phone are also received by indoor
antenna, amplified by the booster and then send back to cell tower by donor
antenna.
( To server ant )
Indoor Port
( From Donor ant )
Outdoor Port
LNA
Duplexer
Drive
PA
LNA
Drive
PA
Duplexer
RF SAW
RF SAW
RF SAW
RF SAW
POWER SUPPLY
DC IN
AC IN
LED Monitor
Attenuator
ATT ALC
ATT
Booster Adapter
(Standard configuration)
Main specification
•
GSM/CDMA specification
Installing your hardware
Before you install
•
antenna location and booster connector.
•
Make sure the position you install the booster is near to one existing electrical
outlet, and well ventilated, away from excessive heat, moisture, and direct
sunlight.
Installation tools and accessories:
Installation overview
•
Install your donor antenna on the roof where there is the strongest signal.
•
Mount your signal booster, connect the cables to the signal booster from the
outdoor antenna and indoor antenna at the designated ports, and connect the
booster to the AC supply(make sure all the cables are connected).
•
Install the indoor antenna where you want to improve the signal.
Find the area with the strongest signal
The booster's main function is to improve weak RF signals of an area. The signal
strength from the outdoor antenna directly affects the efficiency of indoor
coverage.
Make sure you have sufficient cable length between proposed donor/server
User's Manual
GSM/CDMA
Single Band Consumer Booster
Wide Band Yagi Antenna Panel Antenna Whip Antenna
(Optional accessories)
Num.
1
2
3
4
5
Name
Plastic expansion bolt
Tapping screw
Hanging folder
Reciprocating drill
Shot bit
Specification
Ø6
M4*25
Ø6
Quantity
5
4
1
1
1
Remark
Standard accessories
Standard accessories
Standard accessories
Engineering-owned
Engineering-owned
1.Wide Band Yagi Antenna
2.Booster
3.Indoor Panel Antenna
1
2
3
E
A
D
C
B
UL
DL
GSM
890~915MHz
935~960MHz
CDMA
824~849MHz
869~894MHz
Band width
GSM/CDMA
F17
65dB
70dB
F23
65dB
70dB
F17
17dBm
17dBm
F23
17dBm
23dBm
Power Supply
Input AC100~240V.50/60Hz, Output DC5V/3A
RF Parameter
25MHz/25MHz
Max.Gain
Max. output power
MGC (Step Attenuation )
≥31dB/1dB step
Automatic Gain Control
≥31dB
Frequency stability
≤0.01ppm
Electrical Parameter
I /O Port
N-Female
Power Consumption
≤4W
Input & Output Impedance
50 ohm
Indicator
POWER LED
1)Green: Power ON
2)OFF: Power OFF
ISO LED
1)Green:No loop back or no self-oscillation
2)Slow Flashing Green: Slight loop back or self-oscillation
3)Quick Flashing Green: Deep loop back or self-oscillation
4)Quick Flashing Red: Severe loop back or self-oscillation
ALARM LED
1)Green: Output power is not full
2)Slow Flashing Green: Full output power
3)Quick Flashing Green: Output power is over rated
4)Quick Flashing Red: Output power is severe over rated
Mechanical Parameter
Environment Conditions
IP40
Frequency Range
Storage Temperature
-10ºC~+80ºC
Humidity
5% - 95%
Atmospheric pressure
55 kPa -106 kPa
Dimensions
120*135*34mm
Weight
≤0.5Kg
Environment Parameter
Operating Temperature
0ºC~+55ºC
