Amron AMCOM III 2830A/24 User Manual Download Page 5

 

2830A THREE DIVER COMMUNICATOR USER MANUAL 

 

2830A-UM 

REV 5.0 

1  INTRODUCTION AND SPECIFICATIONS 

1.1 

INTRODUCTION 

The  AMCOM  III  series  of  diver  communication  systems  are  full-featured,  hard  wire,  three- 
diver  communicators.  The  AMCOM  III  has  independent  microphone  and  earphone  volume 
controls for each diver and the tender.  

All  AMCOM  III  series  have  push-to-talk,  and  separate  isolated  inputs  for  each  diver.  The 
AMCOM  III  Model  2830A/24  is  a  portable  three  diver  communication  system,  delivering  20 
Watts  of  "voice  power",  operating  from  either  a  110/220  V

AC

,  an  external  12  V

DC

  power 

source, or an internal 12 V

DC

 backup battery. 

The  Model  2830A  has  the  capability  of  2-wire  and/or  Full-Duplex  (4-wire)  communication 
modes. 2-Wire and Full-Duplex (4-wire) modes can be used simultaneously. Full-Duplex is a 
communications  system  designed  from  the  "ground-up"  to  take  advantage  of  the  current 
"state  of  the  art"  in  semiconductor  technology  and  provide  superior  diver  hard  wire 
communication. 

This portable diving communicator has the ability to work with the Dynamic and Pre-Amplifier 
microphone  in  both  2-wire  and  4-wire  modes.  This  unique  design  has  the  ability  to  detect 
both pre-amp and dynamic diver microphones that are in use. This feature will automatically 
switch  from  a  preamp  mode  to  a  dynamic  mode  and  will  adjust  the  specific  diver  gain 
(volume).  

The Model 2830A’s with 20 watt

s of power is the most powerful communicator on the market. 

The  untouched  volume  and  clarity  allows  the  tender’s  volume  to  be  set  at  very  high  levels 

especially in noisy environments while the divers are at a comfortable listening level. 

1.2 

ELECTRICAL SPECIFICATIONS 

Input Impedance (Each Input)  ..................................................................................  250 Ohms 

Frequency Response  ........................................................................................ 300 - 10000 Hz 

Common Mode Rejection (minimum)  ................................................................................ 40 dB  

Current Drain Maximum Full Volume  ............................................................................. 3 Amps 

Typical Quiescent  ............................................................................ 0.25 mAmps 

Minimum Load Impedance  ............................................................................................... 2 ohm 

Nominal Power Supply Voltage  ....................................................................................... 12 V

DC

  

Operational Supply Voltage  ........................................................... 90-264 Volts AC, 47-440 Hz 

Sensitivity (Input)  ..................................................................................................... 0.5 mVRMS 

Maximum Output Power (4 Ohm Load, 14 V

DC

)  ........................................................... 20 Watts 

Battery Life (typical)  ..................................................................................................... 15 Hours 

 

 

Summary of Contents for AMCOM III 2830A/24



















































Reviews: