AMQ ACTIV-Pro Installation Manual Download Page 3

ACTIV-PRO 

INSTALLATION GUIDE  |  3

amqsolutions.com

    

SAFETY STATEMENT

WARNING

RISK OF SERIOUS INJURY DUE TO PINCH POINTS, TIPOVER, OR 
POTENTIAL COLLAPSE.

This powered, adjustable height desk appliance is not intended for use by persons (including children) with 
reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have 
been given supervision or instruction concerning use of the appliance by a person  responsible for their 
safety. Children should be supervised to ensure that they do not play with the appliance.

• 

RISK OF DEATH OR SERIOUS 
INJURY. 

Raising or lowering desk 

cantrap, pinch or crush body parts or 
property.

• 

CRUSH HAZARD - DO NOT PLACE 
FEET, LEGS OR OTHER BODY 
PARTS ON OBJECTS PLACED 
UNDER TABLE TOP OR BELOW 
MODESTY PANEL.

• 

DO NOT OPERATE THIS EQUIPMENT 

Unless Properly Trained.

• 

DO NOT ALLOW USE BY CHILDREN 

or people unable to understand the risks 
and to safely adjust the desk height.

• 

INSPECT REGULARLY. 

Stop using if 

product is damaged or has loose parts. 
Only repair with AMQ authorized parts 
and methods.

• 

MAINTAIN >1” (25mm) GAP ABOVE 
OBJECTS ON DESK AT MAX HEIGHT 
AND BETWEEN THE DESK & 
ADJACENT OBJECTS. 

Locate desk, 

accessories, and nearby objects to 
allow movement of desktop through full range without pulling cords, trapping body parts, or colliding with anything 
(shelves, electrical plugs and cords, door knobs, window sills, storage cabinets, etc.)

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause 
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired 
operation.
This equipment has been tested and found to comply with the limits for a class B digital device pursuant to Part 15 for FCC rules. These 
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, 
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful 
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this 
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and 
on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving 
antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet or a circuit different from 
that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 
Important: Changes or modifications to this product not authorized by AMQ could void your authority to operate the product.

Max.

Min.

>1"

(25mm)

>1"

(25mm)

>1"

(25mm)

X

X

X

NOTE: Desk image

is for reference only.

Table shape and leg

quantity may change

based on the style

and configuration. 

(877) 801-0307

www.amqsolutions.com

?

Summary of Contents for ACTIV-Pro







































Reviews: