Ampere Audio AA-1000.1D Owner'S Manual Download Page 8

Specifications

Continuous Power Output @14.4V Input

T.H.D Continuous @ 4 ohm, 100Hz 
Efficiency @ 4 ohm, 100Hz

Dimensions (mm)

Recommend Fuse Rating

    -RMS power, 4 ohms mono
    -RMS power, 2 ohms mono
    -RMS power, 1 ohm mono 
    -RMS power, 2 ohms linkable/dual mono
Signal To Noise Ratio
Low Pass Frequency Crossover
Subsonic Filter
Bass Boost @ 45Hz
Phase Shift Control
Frequency Response

Input Sensitivity

Operating Voltage

            
                               
                                     

:   300W x 1CH
:   600W x 1CH
: 1000W x 1CH
: 1800W x 1CH
: >90dB
: 35Hz~300Hz
: 10Hz~60Hz
: 0~6dB
: 0~180 degree
: 10Hz~350Hz (+/- 1dB)
: <0.1%
: 86%
: Variable 200mV~6V 
  (+/- 5%)
: 256(W)x55(H)x294(L)
: DC 8.5V~16V
: 30A x 3 (linked: 30A x 6)

AA-1000.1D

MODEL CODE

: 1000W x 1CH
: 2000W x 1CH
: 3800W x 1CH
: 7000W x 1CH
: >90dB
: 35Hz~300Hz
: 10Hz~60Hz
: 0~6dB
: 0~180 degree
: 10Hz~350Hz (+/- 1dB)
: <0.1%
: 86%
: Variable 200mV~6V 
  (+/- 5%)
: 256(W)x55(H)x494(L)
: DC 8.5V~16V
: 200A (linked: 400A)

AA-2000.1D

Continuous Power Output @14.4V Input

T.H.D Continuous @ 4 ohm, 100Hz 
Efficiency @ 4 ohm, 100Hz

Dimensions (mm)

Recommend Fuse Rating

    -RMS power, 4 ohms mono
    -RMS power, 2 ohms mono
    -RMS power, 1 ohm mono 
    -RMS power, 2 ohms linkable/dual mono
Signal To Noise Ratio
Low Pass Frequency Crossover
Subsonic Filter
Bass Boost @ 45Hz
Phase Shift Control
Frequency Response

Input Sensitivity

Operating Voltage

            
                               
                                     

: 1000W x 1CH
: 2000W x 1CH
: 3800W x 1CH
: 7000W x 1CH
: >90dB
: 35Hz~300Hz
: 10Hz~60Hz
: 0~6dB
: 0~180 degree
: 10Hz~350Hz (+/- 1dB)
: <0.1%
: 86%
: Variable 200mV~6V 
  (+/- 5%)
: 256(W)x55(H)x660(L)
: DC 8.5V~16V
: 350A (linked: 700A)

AA-3800.1D

MODEL CODE

MADE IN KOREA

Ampere Audio

17391 Timberland Trail

Flint, Texas 75762

Summary of Contents for AA-1000.1D









Reviews: