background image

CPS-A USER MANUAL 

ISPB028 R1 

 

 

Page 6 

 

Overview of Equipment 

3.1

 

Description 

The Ampcontrol CPS-A Intrinsically Safe Compact Power supply forms part of the Gasguard Range of Group I certified Gas 
Detection and Alarm Systems and is also suitable for use with other applications.  

The CPS series of IS power supplies convert 110Vac mains power to intrinsically safe low voltage DC power. 

The DIN rail mount enclosure is made of robust black polycarbonate. Top and bottom enclosure walls have ventilation slots for 
natural convection cooling. The side walls are solid and allow other components to be mounted adjacent to it on the DIN rail. Top 
and bottom ventilation slots must be kept free for air circulation. Screw terminals are located on the front for connecting the AC 
mains cable and the output load circuits. The output has two terminals for each of the positive and negative DC supply. 

WARNING! 

 

The power supply must be mounted in a safe area or in a suitable enclosure with a minimum 
IP 54 rating. 

 

Typical use of this power supply is for voice communication systems, gas detection systems and other electronic equipment 
requiring intrinsically safe power in a Group I application.  

The CPS-A Power supply is an IP 20 plastic enclosure DIN rail mounting Intrinsically Safe power supply designed for Group I 
applications. Several power output versions of the Power Supply are available with a range of voltage and current limits. 

Mounting is by a moulded clip assembly onto a standard TS32 top hat DIN rail.  

Connections are made to enclosed screw clamp type terminals on the front facia of the enclosure. 

3.2

 

Specification 

Supply Voltage:  

110Vac ± 20%, 50/60Hz 

Operating Temperature: 

   0-50

0

C for 12.6V/2.4A 

 

0-60ºC all other models 

Dimensions:  

125 W x 102 H x

 

122 D mm 

Weight:

  

1kg 

Input Parameter:  

Um = 132V 

Output Parameters:   

Refer Table 3.2 (following) 

Table 3.2: 

Output parameters

 

Uo 

Io 

Co 

Lo 

L/R 

12.6V 

2.4A 

10uF 

74uH 

30uH/Ω 

12.6V 

2.4A 

20uF 

40uH 

8uH/Ω 

12.6V 

2.0A 

20uF 

95uH 

40uH/Ω 

15.1V 

1.5A 

1uF 

190uH 

30uH/Ω 

15.1V 

0.469A 

2uF 

450uH 

70uH/Ω 

15.1V 

0.51A 

2uF 

450uH 

65uH/Ω 

 

Summary of Contents for CPS-A

















Reviews: