manualshive.com logo in svg

AMP Research POWERSTEP 76141-01A, Installation Manual

Share
Download
AMP Research POWERSTEP 76141-01A Installation Manual Download Page 1

www.amp-research.com

1/9

IM76141 rev 01.20.20

I N S T A L L A T I O N   G U I D E

APPLICATION 

  LENGTH  MODEL 

YR 

 PART 

# 

  

Ford F150  SuperCab 

  72”’   

 

2009 - 2014   

76141-01A

Ford F150  SuperCrew    79”               

2009 - 2014  

76141-01A

Ford F150  Regular Cab    55”               

2009 - 2014   

76141-01A

Invented, engineered and manufactured exclusively by AMP Research in the USA. May be covered by one of the following patents:  

6,641,158; 6,830,257; 6,834,875; 6,938,909; 7,055,839; 7,380,807; 7,398,985; 7,584,975   ©2012 AMP Research. All rights reserved.    

Printed in USA.

TOOLS REQUIRED

q

 Safety goggles

q

 8 mm socket

q

 10 mm socket

q

 13 mm socket

q

 13 mm end wrench

q

 Ratchet wrench and extension

q

 Wire stripper

q

  3/16” hex key wrench (allen wrench)

q

  4mm hex key wrench (allen wrench)

q

 Electrical tape

q

  Weather proof caulking (silicone 

sealer)

INSTALLATION TIME

1 2 3

4

SKILL LEVEL

4= Experienced

AMP RESEARCH TECH SUPPORT 1-888-983-2204 (Press 2) Monday - Friday, 7:00 AM - 5:00 PM PST

        

2-3 Hours

Professional installation recommended

5-Year Limited Warranty

WARRANTY

Summary of Contents for POWERSTEP 76141-01A











Reviews:

No comments

Brands by name

Popular brands

Load more brands