amiad SAF-3000 Installation, Operation And Maintenance Instructions Download Page 24

 

SAF 3000 

                                     07.2019 

Page 24 of 25 

AMIAD LIMITED WARRANTY

  

1.

 

This certificate applies to Amiad Water Systems Ltd. ("

Amiad

") products purchased by you (the "

Buyer

") from Amiad unless specifically 

agreed  otherwise  in  writing  by  Amiad.  This  Warranty  extends  only  to  the  original  purchaser,  and  is  not  transferable  to  anyone  who 
subsequently purchases, leases, or otherwise obtains the product from the original purchaser.  

2.

 

Amiad hereby warrants that the products are and will be free from defects in material and workmanship under normal use and service. 
Amiad warrants that it will correct manufacturing defects in the products, in accordance with the conditions set out in this Warranty. 

3.

 

This  Warranty  is  enforceable  for  a  period  of  12  months  after  the  date  upon  which  the  products  were  delivered  (t

he  “

Warranty 

Period

”). 

 

4.

 

In the event that during the Warranty Period the Buyer discovers a defect in material and/or workmanship in any product or part (the 

Defective Product

”), it shall submit a written complaint to Amiad using Amiad's standard Buyer Com

plaint Form. For the receipt of the 

Buyer Complaint Form, the submission of the complaint or any questions please contact your service representative.  

5.

 

Upon written demand by Amiad the Buyer shall return the Defective Product - or a sample thereof - to Amiad, at Amiad's cost. If the 
Buyer ships any such Defective  Product, Amiad suggests the Buyer package  it securely and insure it for value, as Amiad assumes no 
liability for any loss or damage occurring during shipment. Provided however that in the event Amiad determines that this Warranty 
does  not  apply  to  such  product,  Buyer  shall  promptly  reimburse  Amiad  for  such  cost  (including  freight  and  customs).  Any  returned 
product or part must be accompanied by the Warranty certificate and the purchase invoice. It is clarified that the Buyer may not return 
the Defective Product unless such return was coordinated and approved by Amiad in advance.   

6.

 

Amiad's obligation under this Warranty shall be limited to, at Amiad's option, the repair or exchange, free of charge, of the product or 
any part which may prove defective under normal use and service during the Warranty Period. The provision of a repair or replacement 
of  a  product  during  the  Warranty  Period  will  result  in  an  extension  of  the  Warranty  Period  by  an  additional  period  of  12  months, 
provided that the total accumulated Warranty  Period shall in any event be no more than 18 months  from the date upon which  the 
products were delivered.  

7.

 

This  Warranty  is  valid  on  the  condition  that  the  products  are  installed  according  to  Amiad's  instructions  as  expressed  in  Amiad's 
instruction  manuals  and  according  to  the  technical  limitations  as  stipulated  in  Amiad's  literature  or  as  stated  by  a  representative  of 
Amiad.  

8.

 

This Warranty will not apply to damaged or defective products resulting from or related to:  

(i)

 

Fire, flood, power surges or failures or any other catastrophe and/or unforeseen occurrence, such as but not limited to those for 
which the Buyer is customarily insured for, or any force majeure events;  

(ii)

 

Fault, abuse or negligence of the Buyer;  

(iii)

 

 Intake water not meeting the agreed standards, as set forth in a written document, approved by Amiad, or improper storage;  

(iv)

 

Improper or unauthorized use of the product or related parts by the Buyer, including Buyer’s failure to operate t

he product in 

conformity with the recommendations and instructions  of Amiad, as set forth in Amiad's manuals and other  written materials, 
the operation of the product other than by a trained and qualified operator, or improper installation of the product by a third 
party not authorized by Amiad;  

(v)

 

Performance by the Buyer of maintenance or operation other than in conformity with the recommendations and instructions of 
Amiad,  or  other  than  in  accordance  with  procedures  defined  in  the  literature  supplied  for  products  (including  the  timely 
replacement of requisite parts), and for services provided other than by a trained and qualified advanced operator; or 

(vi)

 

Any  alteration,  modification,  foreign  attachment  to  or  repair  of  the  products,  other  than  by  Amiad  or  its  authorized  technical 
representatives.  

9.

 

In no event shall Amiad be liable to the Buyer or any third party for any damages to property, or for any intangible or economic loss, 
including  loss  of  profits,  loss  of  customers  or  damage  to  reputation,  for  any  damages,  including  indirect,  special,  consequential 
damages, or punitive damage arising out of or in connection with this Warranty, or arising out of or in connection with the product's 
performance or failure to perform, even if it has been advised of the possibility of such damages.  

10.

 

Amiad will be excused for failure to perform or for delay in performance hereunder if such failure or delay is due to causes beyond its 
reasonable control or force majeure preventing or hindering performance. 

11.

 

This Warranty set forth herein is the only contractual warranty given by Amiad and is provided in lieu of any other warranties created 
by any documentation, packaging or otherwise.  

12.

 

Amiad makes no warranty whatsoever in respect to accessories or parts not supplied by Amiad. In the event that Amiad is required to 
correct a Defective Product or product not covered by this Warranty, it will do so solely in consideration for additional fees. 

13.

 

The parties will actively endeavor to amicably settle any dispute arising between them. In the event that the parties are unable to reach 
an equitable settlement of such dispute, any claim or lawsuit related to the Warranty, its validity execution, its performance be brought 
before only the courts of Tel-Aviv, Israel. Israeli law will govern the Warranty, to the exclusion of any conflict 

 

 

Summary of Contents for SAF-3000


























Reviews: