amiad EBS-10000 Installation, Operation And Maintenance Instructions Download Page 23

 

 EBS 10000 IL                                                                           910101-000109 / 09.17 

Page 23 of 24 

 

Amiad Limited Warranty  

This certificate a

pplies to Amiad Products purchased by You from Amiad or an Amiad authorized Distributor (“

Distributor

”). This limited 

warranty extends only to the original purchaser, and is not transferable to anyone who subsequently purchases, leases, or otherwise 
obtains the Product from the original purchaser.  

1.

 

Amiad hereby warrants that the Products are and will be free from defects in material and workmanship under normal use and 
service. Amiad warrants that it will correct manufacturing defects in the Products, in accordance with the conditions set out in 
this warranty. 

2.

 

This warranty is enforceable for a period of 12 months after the date Bill of Lading or equivalent (the “

Warranty Period

”). 

 

3.

 

In the event that during the Warranty Period the Distributor discovers a defect in material and/or workmanship in any Product or 

part (the “

Defective Product

”), it shall submit a written complaint to Amiad using Amiad's standard customer complaint form. For 

the  receipt  of  the  customer  complaint  form,  the  submission  of  the  complaint  or  any  questions  please  contact  your  customer 
service representative.  

4.

 

Upon written demand by Amiad the Distributor shall return the Defective Products 

 or a sample thereof 

 to Amiad, at Amiad's 

cost. If the customer ships any such Product, Amiad suggests the customer package it securely and insure it for value, as Amiad 
assumes  no  liability  for  any  loss  or  damage  occurring  during  shipment.  Provided  however  that  in  the  event  Amiad  determines 
that the warranty does not apply to such Product, Distributor shall promptly reimburse Amiad for such cost (including freight and 
customs). Any returned Product or part must be accompanied by the warranty certificate and the purchase invoice. It is clarified 
that the Distributor may not return the Defective Product unless such return was coordinate and approved by Amiad in advance.   

5.

 

Amiad's obligation under this warranty shall be limited to, at its option, the repair or exchange, free of charge, of the Product or 
any  part  which  may  prove  defective  under  normal  use  and  service  during  the  Warranty  Period.  The  provision  of  a  repaired  or 
replacement Product during the Warranty Period will result in an extension of the Warranty Period by an additional period of 12 
months, provided that the total accumulated Warranty Period shall in any event be no more than 18 months from the original Bill 
of Lading.  

6.

 

This warranty is valid on the condition that the Products are installed according to Amiad's instructions as expressed in Amiad's 
instruction manuals and according to the technical limitations as stipulated in Amiad's literature or as stated by a representative 
of Amiad.  

7.

 

This warranty will not apply to damaged or defective Products resulting from or related to:  

(i)

 

Fire, flood, power surges or failures or any other catastrophe/and or unforeseen occurrence, such as but not limited to those 

for which the customers are customarily insured;  

(ii)

 

Fault, abuse or negligence of the customer;  

(iii)

 

Customer's responsibilities, including the failure of the intake water to meet the agreed standards, as set forth in a written 

document, approved by Amiad or improper storage.  

(iv)

 

Improper or unauthorized use of the Product or related parts by the customer, including the customer’s failure to operate the

 

Product in conformity with the recommendations and instructions of Amiad, as set forth in Amiad's manuals and other 
written materials, the operation of the Product other than by a trained and qualified operator, or improper installation of 
the Product by a third party not authorized by Amiad;  

(v)

 

Performance by the customer of maintenance and other services other than by a trained and qualified advanced operator, or 

other  than  in  conformity  with  the  recommendations  and  instructions  of  Amiad,  or  other  than  in  accordance  with 
procedures defined in the literature supplied for Products;  

(vi)

 

Any alteration, modification foreign attachment to or repair of the Products, other than by Amiad or its authorized technical 

representatives.  

8.

 

In  no  event  shall  Amiad  be  liable  to  the  customer  or  any  third  party  for  any  damages,  including  indirect,  special,  exemplary, 
punitive  or  consequential  damages,  or  lost  profits  arising  out  of  or  in  connection  with  this  warranty,  or  arising  out  of  or  in 
connection with the Product's performance or failure to perform, even if it has been advised of the possibility of such damages.  

9.

 

Amiad  will  be  excused  for  failure  to  perform  or  for  delay  in  performance  hereunder  if  such  failure  or  delay  is  due  to  causes 
beyond its reasonable control or force majeure preventing or hindering performance. 

10.

 

The limited warranty set forth herein is the only warranty given by Amiad and is provided in lieu of any other warranties created 
by any documentation, packaging or otherwise.  

11.

 

Amiad  makes  no  warranty  whatsoever  in  respect  of  accessories  or  parts  not  supplied  by  Amiad.  In  the  event  that  Amiad  is 
required to correct a defective Product or product not covered by this warranty, it will do so solely in consideration for additional 
fees.

Summary of Contents for EBS-10000

























Reviews: