background image

Installation Guide & Owner’s Manual  – Under-the-Counter RO & Alkaline Drinking Water System 

 

Copyright © 2019 WaterAnywhere. 

All Rights Reserved.

 

Page 3 

 

 

Conditions 

for 

Operation 

         

Source Water Supply 

Community/Private 

Non-Chlorinated – or chlorinated as long as the carbon filter is in place 
and replaced every 6 months.  Chlorine will damage membranes if not 
removed properly. 

System Pressure 

40 psi minimum - 90 psi maximum 

Temperature 

4º-38º C (40º-100º F) 

Maximum Supply TDS Level 

1500 ppm (mg/L) 

Turbidity 

<1.0 Net Turbidity (NTU) 

 

Chemical Parameters 

Hardness (CaCO3) 

<175 mg/L (<10 gpg)* 

Iron (Fe) 

<0.1 mg/L 

Manganese (Mn) 

<0.05 mg/L 

Hydrogen Sulfide (H2S) 

0.00 mg/L 

Chlorine (CL2) 

0.00 mg/L 

pH 

4 to 11  

*Note that system may operate with higher hardness levels, but the membrane life will be reduced.  Use of a 
water softener for hard water supplies will increase membrane life and efficiency. 

Warnings 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  Only use this system on potable water supplies.  Do not use this system where the 

water is microbiologically unsafe or of unknown quality. 

  Never use hot water or allow the unit to freeze. 

  Incorrect installation or operation will void the warranty. 

  Excessive incoming water pressure can cause leaks, flooding and property damage.  It 

is highly recommended to monitor your home’s incoming water pressure over a period 
of 24 hours to determine if a pressure regulator is required. 

  Manufacturer assumes no responsibility for damages incurred through improper 

installation or use of these products. 

  Ensure that all tubing and fittings used for RO product water are poly material, and not 

copper.   Due to RO product water being very pure, it can leach the minerals from 
copper tubing which will cause a metallic taste in the water or ice and cause the copper 
tubing to develop pinhole leaks over time. 

 

 

 

Summary of Contents for AAA-N50W





















Reviews: