background image

Installation Guide & Owner’s Manual  – Under-the-Counter RO & Alkaline Drinking Water System 

 

Copyright © 2019 WaterAnywhere. 

All Rights Reserved.

 

Page 12 

 

 

System Mounting 

 

 

 

 

 

 

 

 

 

 

 

Wall mounting is recommended for this system.   Dry wall anchors and screws may be necessary (not included 
with the system). 

  Mark screw locations at the desired positions.  Use the two holes on the back of the RO System mounting 

bracket for marker guides. 

  Screw the screws into the mounting wall on the marked positions.  Use an anchoring device appropriate for 

the type of material you are screwing into. 

  Hang the purification system onto the screws by the holes on the back of the unit. 

 
 

Turning the System On for the 

First 

Time 

     

Make sure all water supply and drain line connections are secure and free from leaks. 

Slowly turn the feed valve counterclockwise until fully open (the handle should be in line with the tubing as it 
enters the connection).   Check the stem seal for leakage.  If necessary, tighten stem nut lightly. 

Turn storage tank valve one quarter turn counterclockwise to open the valve (the handle should be in line with 
the tubing as it enters the connection). 

Open the product water faucet and let the water flow until all the air has been expelled from the system.  This 
will take about an hour. 

Close the product water faucet.  In 30 minutes, check the system and connections for leaks and correct if 
necessary. 

 

Do Not Use the First Two Reservoirs of Water 

Allow the reservoir to fill for 4-6 hours.  Dispense this water to drain.  This process 
removes the factory installed sanitizing solution from the entire system and sends it to 
the drain.  Repeat this process one more time.  Allow the tank to fill for 4-6 hours and 
dispense this water to the drain.  Do not drink this water! 

 

 Notice:

 

Air bubbles may be present in the product water after initial system startup, causing 
a milky color in the water.  This is normal and safe to drink.  The air bubbles will 
disappear within a few days of regular use. 

 

 

 Notice:

 

Check back frequently in the first 24 hours to ensure no leaking has occurred. 

 

 

 

Summary of Contents for AAA-N50W





















Reviews: