background image

UltraMig 175 

- 4 - 

Safety Instructions 

 

 

1. Safety in the use of a power source 
for electric arc welding 

 
The equipment which you have just acquired will give 
you complete satisfaction if you follow the operating 
and maintenance instructions. 
 
Its design, specification of components, and its 
manufacture are in accordance with CE and ULC 
standards. 
 
When using this equipment, safety rules must be 
observed, especially those concerning power sources. 
 
For your safety, you will find listed below a complete 
set of recommendations or requirements as found in 
government labor safety codes. 
 

2. Work station 

 
The use of arc welding equipment requires the 
establishment of strict safety conditions with regard to 
electrical currents. 
 
It is necessary to check that no metal on which an 
operator will be working can come into direct or indirect 
contact with a phase conductor and the ground of the 
electrical supply network. 

 

All ground cables for the welding operation that are 
within reach of the user should be connected to a 
single point. 
 
All extension cords must be made with cables whose 
wire size is at least equal to that of the largest power 
cable. 
 
If welding work has to be carried out in a confined 
space, the following extra precautions should be taken: 
 
• Increased individual protection. 
 
• Complete insulation of the electrode holder, torches 
or guns. 
 
• The welding machine itself should be kept outside the 
confined space and if this is not possible, the low 
voltage parts of the equipment should be insulated and 
the workpiece ground cable should be held in place by 
solder. 
 
 
 

 

3. Servicing 

 
Before beginning any inspection or repair of the inside 
of the machine it is necessary to make certain that the 
equipment has been disconnected from the electrical 
circuit by lockout and protective devices: 
 
• The plug must be removed from the socket and 
provisions are taken to prevent the accidental 
connection of the plug in a socket. 
 
• All cutout switches for fixed connection systems 
should be omnipolar (phases and neutral).  Such 
switches must be in the "OFF" position, and secured or 
“locked out” so that they cannot be accidentally put into 
opération. 
 
• Maintenance work on electrical equipment must be 
undertaken only by persons qualified to do such work. 
 

4. Wire feed devices 

 
Make sure the wire or torch cannot touch  any metal 
parts, including the inside of the cabinet. 
 
Do not allow the wire outlet or torch to point toward 
your face or body. 
 
Gloves should be worn when handling wire. 
 

5. Maintenance 

 
The insulation of equipment and the electrical 
accessories must be checked regularly and kept in 
good condition.  This includes plugs, flexible cables, 
sheaths, connectors, extension cords, workpiece 
clamps or torches. 
 
Maintenance and repair work on insulating sheaths and 
covers should never be done in a makeshift manner. 
 

AS REQUIRED: 

 
• Replace defective accessories where possible.  
Repairs should only be made by a trained specialist. 
 
• Electrical connections must be checked regularly for 
proper tightening and to insure they are not 
overheating. 

Summary of Contents for UltraMig 175























Reviews: