background image

UltraMig 175 

- 13 - 

3. Aluminium welding 

 
A. Aluminum welding with a standard torch normally 
requires the installation of a teflon liner in a size to 
match the gun and cable assembly. 
  
B. Reduce the tension on the upper drive wheel.  
There should be just enough drag to feed the torch 
without damage to the aluminum wire (see fig.). 
 
C. Use only 100% argon inert gas with 14 to 18 l/min 
flow rate. 
 
D. Always "PUSH" the weld bead with aluminum to 
keep the gas "IN FRONT" of the welding. The argon 
will provide the inert shield for a clean weld. E) Use a 
stainless steel brush to clean the aluminum before the 
welding. 
 
F. Begin with a low power setting and gradually 
increase it obtain a smooth, even weld.  
 
G. As aluminum is an excellent heat conductor, it will 
be necessary to decrease the power after few 
centimetres (inches) of welding. 
 

NOTE

: Always use a contact tip one size bigger then 

the aluminum welding wire selected. 

Ex: for a wire of 

0.8mm (.030”), use a contact tip for a wire diameter 
of 0.9mm (.035”)

4. Spot welding 

 
Spot welding can be done through two thickness of 
sheet metal. However, the best results are obtained by 
drilling or punching a hole the top piece. 
 
A. In case of spot welding through two pieces of sheet 
metal, both pieces should be clean, properly aligned, 
and securely clamped together. 
 
B. Install the spot weld nozzle on the torch. 
 
C. Adjust the power to obtain a flat bead. If possible, 
test the setting on a sample made with the same 
sheets of metal to be spot welded. 
 
D. Hold the torch perpendicular to the work surface 
with the two spot nozzle legs touching the metal and 
pull the trigger. 
 
E. In case of welding in a pre-drilled hole, center the 
spot nozzle above of the hole and fill it up.  
 
F. When working without a pre-drilled hole it will be 
necessary to turn up the power high enough to 
penetrate the top sheet of steel. 
 

 

 

 
G. When a spot nozzle is not available, use a standard 
conical welding nozzle and maintain a distance of 
6mm to 12mm between the nozzle and the sheet 
metal. 
 

5. Stitch welding 

 
Stitch welding is a convenient process to use when 
welding rusty or thin material, and where there is a risk 
of deforming or burning through the metal.  A stitch 
weld actually consists of a series of spot welds strung 
together.  A short gap between each stitch allows the 
piece of steel to cool down. 
 
A. Select a power setting appropriate for the thickness 
of the piece of steel. 
 
B. Hold the trigger and move slowly along the welding 
line while maintaining the angle to and distance from 
the work. 
 
C. The gap between each stitch should be long 
enough to allow the orange color of the preceding weld 
to disappear. 
 
A build in “post” gas flow of 1 sec. keeps the gas valve 
open after the arc stops providing better cooling before 
the next weld. 

6. Filling holes 

 
A. Throughly clean the edges of the hole. 
 
B. Make a short weld at one spot on the edge of the 
hole and let cool. 
 
C. Make another short weld on each side of the first 
weld and let them cool. 
 
D. Make two longer welds overlapping the first three 
with an arching movement of the torch.  Again, allow 
the welds to cool. 
 
E. Repeat the same technique on the other side of the 
hole and across the top of the hole, if necessary. 
 
F. Long, narrow gaps may also be easily filed and 
closed by using the stitch welding mode.

 

Summary of Contents for UltraMig 175























Reviews: