background image

AMG Systems Ltd. reserves the right to make changes to this document without
notice. The information herein is believed to be accurate. No responsibility is
assumed by AMG for its use.

Page 2 of 6

AMG2648R Instruction
Sheet D15534-01

Optical Connections

OPTO OUT
Connector ............................................FC/PC
Optical Launch Power ......................... -5dBm
Wavelength .......................................... 1310nm

Note: - The transmission distance on multimode fibre will tend to be limited by the bandwidth of the
fibre rather than the optical dynamic range. It is recommended that 50/125 optical fibre is used as this
will have a higher bandwidth than 62.5/125 fibre. The

AMG2647

and

AMG2648R

will transmit and

receive over a minimum of 1km of 62.5/125 fibre and will typically transmit and receive over 2km of
50/125. The transmission distance will typically be longer than this but will depend of the performance
of the optical fibre.

OPTO IN
Connector ............................................FC/PC
Optical Sensitivity ................................ -22dBm
Wavelength.......................................... 1310nm

Power Connection

Power supply ....................................... from plug in connection on the 2000 or 2005 subrack
Power consumption ............................. 12 Watts max.

Indicators

Power................................................... Green

– unit powered

Off

– no power applied to unit

Opto Sync RX ...................................... Green

– optical channel receiving

Off

– optical channel not receiving

Opto Sync TX ...................................... Green

– optical channel transmitting

Off

– optical channel not transmitting

Video Present ...................................... Green

– video signal present on video the channel

indicated.

Red/Green – video channel available on the fibre but no

video signal being transmitted

Off

– no video channel available on the fibre.

(when data slot contains a data daughter board)
Data Present TX .................................. Green

– logic one present on the data input

Red

– logic zero present on the data input

Off

– tri-state off or no connection on the data input

This represents the data signals being transmitted on the optical fibre

Data Present RX .................................. Green

– logic one present on the corresponding data

output
Red

– logic zero present on the data output

Off

– tri-state off on the data output

This represents the data signals being received on the optical fibre

(when audio slot contains an audio daughter board)
Audio Present TX ................................ Green

– when an audio level between –40dBm and

+0dBm is on the audio input (600ohm).

..................................................... Red

– when an audio level above 0dBm is on the

audio input. (600ohm).

..................................................... Red/Green – when an audio level peaking above 0dBm is on

the audio input. (Note audio daughter board will
accept up to +6dBm (600ohm)).

..................................................... Off

– when an audio level is below –40dBm on the

audio input. (600ohm).

This represents the audio signals being transmitted on the optical fibre

Summary of Contents for AMG2648R







Reviews: